查询词典 pillar bolt

Analyzed the structure characteristics of the perfume cover outer shell plastics piece, described the piece's structure and work principle which model a craft and inject a mold, its principle :adopt and certainly be apart from bolt and spring coil and carry on two cents type, use inclined lead a side outside the pillar and take out heart, type the heart crest spare parts, while entering and anticipating adoption incubate the type sprinkle into anticipate a form, while opening a mold, with the ball head pull and anticipate a pole sprinkle and note system and anticipate, then make use of and take out and push plank and release a plastics piece inside a heart,use spring coil and reset first while matching a mold, then carry on willing model a beginning next time.

摘要分析了香水盖外壳塑件的结构特点，叙述了该塑件成型工艺、注射模的结构和工作原理，其原理是：采用定距螺钉和弹簧进行二次分型，用斜导柱外侧抽芯，型芯顶出零件，进料时采用潜伏式浇口进料形式，当开模的时候，用球头拉料杆把浇注系统凝料顶出，然后利用型芯内抽推板推出塑件，合模时用弹簧先复位，然后进行下一次成型开始。

When the hydraulic pressure power supply stops or controls the solenoid valve opens, in driving pliers' pressure oil pressure vanishing, the piston under the precompression brake block spring's function rapidly promotes, affects on the friction liner and presses to is applied the brake the body, simultaneously the driven pliers in the driving pliers and under connecting bolt's function, lead through the glide guide pillar's function rub the liner to press to are applied the brake the sleeve to become the brake.

当液压动力源停止或控制电磁阀打开时，主动钳内的压力油压力消失，活塞在预压的制动弹簧的作用下迅速推出，作用在摩擦衬垫上并压向被制动体，同时从动钳在主动钳和连接螺栓的作用下，通过滑动导柱的作用带动摩擦衬垫压向被制动体完成制动。

In this paper,the deformation law of supporting coal pillar at Sanbula district is analyzed by using numerical simulation and the reasonable size of coal pillar and the parameter of bolt in the entry is got.

采用数值模拟方法对天隆集团公司三不拉采区支撑煤柱的变形规律进行分析，得出了该采区的合理支撑煤柱尺寸以及巷道锚杆支护参数，对设计和施工有参考作用。

In order to determine the size of coal pillar scientifically and reasonably, we mainly studied the law of stress distribution of the surrounding rock and the mechanism of narrow pillar drift and high strength bolt support and so on, indicating that using the narrow pillar drift and high strength bolt support can effectively guarantee the stability of gob-side entry in deep mine.

为科学合理地确定煤柱尺寸，保证沿空巷道的稳定，研究了沿空巷道的围岩应力分布规律、小煤柱护巷机理以及高强锚杆支护。从理论上证明了采用小煤柱护巷及高强锚杆支护方式理论上能够有效地保证深井沿空巷道的稳定。

The connection between the bottom support board and the pillar should reserve the foot bolt hole, the hole sizeshould be bigger than or be equal to three times of the diameter of the feet bolt, the depth slightly is bigger than the foot bolt length. Pouring into the epoxy resin mortar into the hole, its mixture ratio is the epoxy resin (6,101), DBP17, ethylenediamine 8, and granulated substance

下支座板与墩台的连接则应预留地脚螺栓孔，孔的尺寸应大于或等于三倍地脚螺栓的直径，深度稍大于地脚螺栓的长度，孔中灌注环氧树脂砂浆，其配合比为环氧树脂（6101），二丁脂17，乙二胺8，砂250。

Of a dish and a dish use the work word steel the welding pays to accept, a dish inner part adoption the Cape iron and the slot steel welding become whole framework, because of conveyance space limit, each dish is divided into two part, combination hour in the interval adoption M18 fix the stud bolt connects with each other to counteract the electric welding 焊 dead, the shape bottom use 8100 mms work word steel welding be used as to pay to accept, and with before install work well of the cement pillar foundation sprinkle to cast into the integral whole.

圆盘与圆盘之间用工字钢焊接支承，圆盘内部采用角铁与槽钢焊接成整体骨架，由于运输空间限制，每一圆盘分为两部分，组合时其间采用M18固定螺栓相连并用电焊焊死，造型底部用8根100mm工字钢焊接做为支承，并与安装前做好的水泥柱基础浇铸成一体。

The support and the pillar and between the girder suitably it should adopt the foot bolt, the slip joint to connect, between the support and the pillar and between the support and the girder, details as follows

支座与墩台和梁体之间宜采用地脚螺栓、套筒连接，详述如下

This is not an ordinary box, which is used as a background picture of the dialog box, very pretty.

详细说明：这可不是一个一般的对话框，它是用图片作为背景的对话框，非常好看。

Conceal me what I am,and be my aid for such disguise as haply shall become the form of my intent.

遮掩我的身份，帮助我，我的面具将成为我的目的。