查询词典 piercing

Swelling after piercing is the most common complication and jewelry in place should not be removed until after four weeks after piercing.

穿孔后肿胀是最常见的并发症和地方首饰不应该删除，直到经过4周后穿孔。

Swelling after piercing is the most common complication and jewelry in place should not be removed until after four weeks after piercing.

穿孔后肿胀是最常见的并发症和首饰到位不应该删除，直到经过4周后穿孔。

Hospital safety is the most reliable variable for predicting health care staff's handling of piercing injuries, and it is the most important factor for preventing piercing injuries and exposure to blood/bodily fluids.

预测变项中以安全气候对医疗工作人员扎伤及血液、体液暴触之行为的预测力最高，安全气候之於扎伤及血液、体液暴触防治中的角色最为重要。

American 76 mm armor-piercing projectiles penetrated the Tiger-B tank's side plates at ranges 1.5 to 2 times greater the domestic 85 mm armor-piercing projectiles.

美国的76毫米炮穿透虎王侧面装甲的距离要比苏联的85毫米炮要大1.5到2倍。

If you get your piercing done with a gun and have an earring literally shot into your earlobe, tiffany pendents , necessities , you'll find that that ends to give you a piercing at an 18 gauge.

如果你的穿孔这方面做了枪，并开枪的耳环字面到您的耳垂，蒂芙尼吊坠，必需品，你会发现结尾，让您在一个18针一穿孔。

In the article,summarizing the surperalloy seamless pipe production since 1960s in China,the main technological problems of the piercing of less-deformable steel and alloy on two-high skew piercing are discussed.

文摘：结合国内从60年代开始的高温合金无缝管材的试制和生产，对难变形钢和合金管坯在二辊斜轧穿孔机上穿孔的主要技术问题进行了讨论和总结。

In the article,summarizing the surperalloy seamless pipe production since 1960s in China,the main technological problems of the piercing of less-deformable steel and alloy on two-high skew piercing are discussed.

田党结合国内从60年代开始的高温合金无缝管材的试制和生产，对难变形钢和合金管坯在二辊斜轧穿孔机上穿孔的主要技术问题进行了讨论和总结。

Parts of the Process Analysis、Process improvements、Die with a complete composite blanking process Piercing 、Expounded washers composite Die Blanking the overall structure and characteristics of the process, Should pay attention to the issue of sexual and assembly process ,Piercing the settlement sheet、 And seam compound die punch slender easily broken、Hole coaxial hard to ensure the short life and die of technical problems.

通过对零件的工艺分析，改进了工艺方案，用一套复合模完成落料冲孔工序，阐述了垫圈冲裁复合模具的整体结构特点及工作过程，应注意的问题和装配工艺性。解决了薄板冲孔、冲缝复合模的凸模细长易断、孔的同轴度难以保证以及模具使用寿命短的技术问题。改进了落料、冲孔、冲缝的制作工艺，设计了一套新型复合冲裁模，提高了工件的同轴度精度，延长了模具的使用寿命。

The pain of losing her Son was like a sharp and merciless sword piercing Mary's soul.

丧子之痛，像是无情的利刃刺透了马利亚的心。

The German 88, without doubt the best artillery piece of the war, in the opinion of every GI, was a high-velocity, flat trajectory weapon that could fire armor-piercing shell down the lanes and roads of Normandy, or be elevated and fire high-explosive airburst shells against Allied bombers.

德军88口径炮——所有美军均认为，88口径炮无疑是此次大战最好火炮——为高射速，可平射之武器，其发射之穿甲弹可打穿树篱，打到诺曼底篱间小径和公路上，也可以昂起炮口，以发射高爆空炸弹头打击盟军轰炸机。

After explaining total design of automated test system for microcircuit , the thesis introduces GPIB standard .

文章在说明了微电路模块自动测试系统的总体设计后，对GPIB标准进行了介绍。

He interceded in my behalf.

他替我说情。