查询词典 pattern die

The endometrial echo patterns visualized sonographically were divided into three categories by Gonen: pattern A: present a triple-line pattern or multilayered endometrium in which hyperechogenic outer lines and a well-defined central echogenic line were visualized, with hypoechogenic or black areas seen between lines; pattern B: present an echo pattern in which the endometrium had the same echogenicity as the myometrium, the central echogenic line is dim; pattern C: present a homogenous endometrium with no central echogenic line.

按照Goden等人的分型标准，晚滤泡期子宫内膜在超声下可以分为三种类型：A型：即三线型，为外层及中部强回声，外层与宫腔中线之间为低回声区或暗区，宫腔中线回声明显；B型：为均一的中等强回声，宫腔中线回声不明显；C型：为均质强回声，无宫腔中线回声。

According to the concept of synergetics, pattern formation and pattern recognition are formally analog. In a pattern recognition process, one can consider a deformation between the stored prototyped pattern and the test pattern to be recognized.

根据协同学概念，模式形成与模式识别具有形式上的相似性，识别过程可考虑在要识别的输入测试模式与存储的原型模式之间的变形。

The system could complete parameterized design of parts and die parts drawing, the virtual assemkbly of die and die assembly drawing, and animated die drawing.

并基于SolidEdge平台，采用参数设计技术和VisualBasic工具，开发了一个圆筒形零件拉深模具系统，该系统能够全参数化进行零件设计并生成零件图、模具虚拟安装并生成模具装配图。

Put die on the die seat, adjust cross- plate and transducer draging plate of up and down, so that the steel needle can be inserted into die hole to adjust the pressure of weight, and then place the abrasive, open power switch of ultrasonic and rotating switch of die seat.

模具放在模座上，调节十字脱板及换能器上下拖板，使钢针插入模孔内，调整砝码压力，然后放上磨料，打开超声波电源开关和模座旋转开关。

With the help of the concepts of Lebesgue measure and Lebesgue integral in real function,the mathematics model of concurrent design of life-oriented progressive die is advanced. Which were the Lebesgue measure and Lebesgue integral of die substructures and a general mathematics model of the relation between progressive die structure and die substructures.

运用实变函数中的Lebesgue测度和Lebesgue积分的概念，结合面向寿命的级进冲模并行设计的特点，建立了面向寿命的级进冲模并行设计数学模型—模具子结构的Lebesgue测度和Lebesgue积分，提出了级进冲模结构与模具子结构关系的一般数学表达式。

Select high-quality die-cutting tool to be considered depending on the die-cutting materials of munltivariable and gaofeng and gaofeng coilia, short peaks can cut thin paper knife and cut thick paper, you can use the automatic single die-cutting, it may be used at the same time cutting two or three sheets of paper-a set of die-cutting, use a wide range.

选择优质的模切刀时应注意根据所模切材料的厚薄而选择高峰刀及矮峰刀，高峰刀既可以切薄纸又可以切厚纸，既可以用在单张的自动模切机上，又可以用在同时模切二、三张纸的手摇模切机上，使用范围很广。

Deep drawsmay be made on single-action dies,where the pressure on the blankholder is more evenly controlled by a die cushion or pad attached to the bed of the press,The typical construction of such a die is shown in Figure 10-6.this is an inverted die with the punch on the die's lower portion

深drawsmay作出对单动去世后，那里的压力就压边的是，更多的控制，由一个模垫或垫附于床的新闻，典型建筑这样一个死硬的是表现在图10 - 6.this是一个倒模与冲床对模具的上半部分。

Besides expressing design result, it provides domain constraint for design process and model information for digital assembly sequence planning and simulation of stamping die, which is usually ignored in the former product models. Taking the specific structure and design process of stamping die into account, the information of workpiece is composed in die product model as product feature. Former product models merely contain mainly about the die design result, this model extends the contents of product model with the relation feature of the composed subassembly and parts and also other associated production knowledge. It is convenient for getting the associated information during intelligentized design process.

该模型不但能完整地表达冲模的设计结果，同时还表达和存储了冲模设计的知识信息，能较好地为冲模的设计过程提供规则和约束，支持产品的智能设计过程以及冲模的数字化预装配规划和仿真；而模型中冲压件信息的集成则扩大了冲模产品模型的信息内涵和应用外延，便于建立冲模智能设计过程的信息关联，从而使集成信息模型成为产品设计过程上、下游活动实现信息共享的基础。

It will be drawn into the die without allowing wrinkles to form Another type of drawing die for use in a single-action press is shown in Figure10-4 this die is a plain single-action type where the punch pushes the metal blank into the die ,using a spring-loaded pressure pad to control the metal flow.

它会被卷入模具而不让皱纹形成另一种类型的拉丝模使用于单动压力机是表现在图形10 - 4这个模具是一个浅显的单动式如冲床把金属毛坯到死了，用弹簧垫，以控制金属流。

Type ZZM-10A cutter sharpener is applicable to grind milling cuttrt of all kinds of diameter,shapes and angles for die sinker,also to die pin corres ponding to the miller according to die sinker scale,it has ability of grinding turning tool,drill.So it is a necessary equipment in using die sinker with excellent figuration,new stucture and good application.

ZZM-10A型万能磨刀机，造型美观，结构新颖，使用性能良好，用于刃磨刻模铣床的各种直径、形状及角度的铣刀和按刻模比例与之相适应的靠磨削，因此它是刻模铣床使用中必需的配套设备，并有刃磨车刀、立铣刀、钻头的功能和装置。

He tendered his resignation to the Prime Minister.

他向首相递了辞呈。不适合

International economy and trade,Nanking 210044

国际经济与贸易，南京 210044