查询词典 optimum programming

The LSSVM (Least Square Support Vector Machines) was proposed to construct multi-objective optimization model for CWM concentration and ball mill electric current. MODE (multi-objective differential evolution) based on Pareto optimal concept is used to perform a search for determining the optimum solutions, from which the optimum adjustment mode that could heighten concentration and production benefit of CWM is obtained based on fuzzy theory.

利用最小二乘支持向量机对球磨机电流和水煤浆浓度进行多目标建模，并采用基于Pareto最优概念的多目标微分进化算法，对运行工况进行寻优，然后根据模糊集理论在Pareto解集中求得满意解，获得水煤浆浓度的优化调整方式和提高水煤浆生产效益的策略，用以指导水煤浆优化生产。

Energy requirement for drying could be reduced by a dryer with a heat recovery device. In order to analyze the optimum operation conditions, the effect of fan speed on the temperature, airflow distribution and effectiveness of the heat recovery device was investigated in the drying system. The optimum fan speed would be at maximum speed during initial heating stage and at lower speed during steady stage in order to improve the performance.

具有热能回收装置的乾燥系统能降低乾燥所需的能量，为了分析此乾燥系统的最佳操作条件，测试其风扇转速对於乾燥室内温度、风速和热能回收装置效能的影响，归纳出风扇最佳运作应是在加热启动阶段应用最快转速，到达稳定阶段后，以较低转速可提升乾燥机的性能。

Very little has been published on the optimum flow rate for particular materials and even if this were known the relationship between optimum flow rate and gate width would probably be complex because of the large number of variables involved.

在特定材料的流动速率优化方面，已经发表的文献很少，并且即使已知优化流动速率和浇口宽度之间的关系，也会由于包含很多变量而使得情况变得复杂。

The optimum temperature of protease, lipase, and cellulase was 50℃, 40℃ and 40℃ respectively in both foregut and midgut, while the optimum temperature of amylase was 40℃ in foregut and 30℃ in midgut.

前肠和中肠中蛋白酶活力均在反应温度为50℃时达到最大值，前肠和中肠中脂肪酶和纤维素酶均在反应温度为40℃时达到最大值，而前肠和中肠中淀粉酶最适反应温度分别为40℃和30℃。

The author also studies the relationship between the maximum friction coefficient, optimum slip ratio, friction coefficent with locked wheels and three parameters in friction coefficient function of slip ratio, and three fit functions derived from experimental analysis, maximum friction coeffient, optimum slip ratio and friction coefficent v~ ith locked wheels, of aircraft speed.

利用试验数据研究了最佳滑移率、结合系数最大值和机轮抱死时的结合系数随飞机速度的变化规律。两者联系在一起，便得到了结合系数随飞机速度和滑移率的变化规律。它是本文的创新点之三。

The optimum conditions were as follows: 1 Fe3+/Fe2+ was 1.70-1.75;2 the precipitant,25% ammonia water was used 20%-30%,under 35℃,pH10-11 and with a stirrer speed of 3000 r/min for 1 h;3 in the first package process with gelatin and agar,the optimum amounts was 0.050-0.060g/150mL at the temperature of 55-60℃ and pH of 9-11;In the f...

最佳工艺条件为：(1)Fe3+/Fe2+之比在1.70~1.75；(2)沉淀剂25%NH3.H2O过量20%~30%，温度35℃，pH值11，反应时间为1h；(3)琼脂的最佳用量为0.050~0.060g/150mL；包覆的最佳温度为50~60℃，pH值为9~11；聚乙二醇作为第二次包裹剂时，最佳温度为55℃，反应时间是1h，pH值为4~5；并用透射电镜、分光光度计、古埃磁天平等进行了初步表征。

The case of a bus route in Qinghuangdao was studied. The analysis results show that the efficient way to improve bus accessibility is to keep bus headway not more than 5 min, so that the optimum bus-stop spacing is below 600 m no matter how much the bus passenger demand is. But on condition of higher bus headways, optimum bus-stop spacing should be in the range of 900 to 1400 m and the bus accessibility would drop more remarkably compared with lower bus headways.

以秦皇岛公交线路为实例，结果显示提高公交可达性的有效途径是使用不大于5min的低发车间隔，无论公交客流量大小，最优公交站距都可以保持在600m以下；而对高发车间隔，公交站距在900~1400m才能获得较高的可达性，而相比低发车间隔，公交可达性显著下降。

Based on the research on the meshing between hobs and gears the optimum proflie design method of the pre-gringding hob is given,and the optimum profile of the pre-gringding hob used to cut the quasi high-speed locomotive traction gear has been designed according to the application of the traction and their proceeding technolog.

通过对刀齿啮合关系的研究，提出了磨前滚刀齿形优化设计方法，针对准高速机车牵引齿轮的应用和加工工艺特点，对准高速机车牵引齿轮磨前滚刀齿形进行了优化设计。

The structure parameters of the Hourglass rubber spring have been optimized for fulfilling the optimum nonlinear stiffness curve. The optimization result indicated that Using of rubber spring with optimum nonlinear elasticity character resulted in good and constant ride comfort of the truck.

以此曲线为优化目标，完成了新型悬架橡胶弹簧结构参数优化；优化后的橡胶悬架系统能使车辆具有良好的平顺性和稳定性。

Based on the optimum quadratic performance index, the optimum guidance law is deduced to make sure the landing velocity and angle of warhead.

基于常值最优二次型指标推导得到了对弹头落地速度以及落地角度有所保证的最优制导律。

Continuously improve the production mechanism, to provide customers with better quality products and services.

不断的完善生产机制，给客户提供更优质的产品及服务。

B:Yes, he was the very prize-winner in the court tennis ten years ago?

是的，他是十年前的世界网球冠军。