查询词典 normal bend

The method which is used to measure and compute moment, yield and turning angle by steel bar gauge is introduced in detail. According to the measuring results, the horizontal critical load of the testing pile is 120 kN. The steel bar gauge measuring results show that the largest moment is located in the depth from 2 m to 3 m under the horizontal load, it transfers to the deeper location with the increase of the horizontal load, and the bend distortion only occurs in the upper of 1/3 pile length.

结合实际工程详细地介绍了利用钢筋计测试水平荷载作用下桩身弯矩、挠度和转角分布的方法，根据桩顶位移和钢筋内力测试结果判定试验桩的水平临界荷载为120 kN；根据钢筋计测试结果可知，在水平荷载作用下，桩身最大弯矩截面位于在地面以下2～3 m处，且随着荷载的增大最大弯矩截面逐渐向深部转移；发生弯曲变形的部分主要是桩长1/3以上的桩体，而其下的桩体几乎不发生变形。

It comprises an in-put shaft hinged to its yoke through one axis, and an out-put shaft also hinged to its yoke through another axis, and these two yokes (13) were combined together by only one axis position, perpendicular to that two yoke axes like a cross, so that this combined axis will bend just like the angle bisector of that two shafts to maintain its constant velocity by a few methods, firstly, by using a section of gear teeth mesh at both ends of the shafts' teeth were so polished so that it can turn longitudinally as usual gear, and also sideways, to provide a larger solid angle of turning from ordinary 45 degrees into 60 or even more.

它包括输入轴，其通过一根轴铰链连接于叉形支架，和输出轴，其通过另一根轴也铰链连接于其叉形支架。并且这两个叉形支架(13)只需用一根相对垂直铰链轴相连而组合在一起，使得这种组合的轴总能形成这两个轴的角平分线，以通过少数几种方法保持其恒速，首先，通过用啮合在轴的两端的一段齿轮齿抛光为以能够像普通齿轮一样纵向转动，并且还能够侧向转动，以提供较大的转向立体角，从通常的45度变成60度或更大。

As the jacket is bent or twisted, adjacent engagement elements move together into engagement with each other, limiting the bend radius or twist angle of the jacket, and thus of the fiber optic ribbon cable or other protected line.

当护套弯曲或扭转时，毗邻的约束零件一起移动进入彼此咬合的状态，从而限制护套的弯曲半径或扭转角，并借此限制带状光缆或其它被保护的导体的弯曲半径或扭转角。

During the summer monsoon the center of the anticyclonic eddy, breaking off from the Kuroshio bend, can reach about°E and the eddy shedding periods are mainly 40-120 days.

夏季风期间，从黑潮弯曲中脱落的反气旋涡的中心位置可以达到117°E附近，反气旋涡脱落的周期集中在40-120天间。

The dominant mechanism of the periodical variation of the Kuroshio bend and the breaking off of anticyclonic eddies is the frontal instability.

非线性平流作用是吕宋海峡黑潮弯曲发生周期性变化的主要原因，吕宋海峡黑潮锋附近的锋面不稳定机制是决定黑潮弯曲周期性变化及反气旋涡从黑潮弯曲中脱落的主要物理机制。

E-117. 5°E . During the winter monsoon the location of the centers of the anticyclonic eddies, shedding from the Kuroshio bend are mainly at the east to 118°E and the eddy shedding periods are basically 40-90 days.

冬季风期间，从黑潮弯曲中脱落的反气旋涡的中心位置基本集中在118°E以东，反气旋涡脱落的周期集中在40-90天间。

Neural tube was formed by the apophysis,bend and close of neural crest.

它们在病因学上是多因素的，是遗传学因素和环境因素共同作用结果。

On the arc of history and bend it once more toward the hope of a better day.

他们的双手扭转了历史，让历史转向充满希望的新的一天。

The result demonstrates accent of true and false in 34 AD 34, inside diaphragm 27, the haematoma inside the wall interlining of model of 7;27 exemple is three-dimensional into resemble all showing clear crevasse, crevasse of aorta bend ministry with arrowy shape show optimal, fall aorta crevasse shows with position of axle and coronal shape optimal, VRT shows pathological changes whole journey is clearer, but reach to crevasse inside the indication of diaphragm reachs position of axle as MIP, MPR.

结果34例AD中显示真假腔34例，内膜片27例，壁内血肿7例；27例典型夹层三维成像均显示明确破口，主动脉弓部破口以矢状位显示最佳，降主动脉破口以轴位及冠状显示最佳，VRT显示病变全程较清楚，但对破口及内膜片的显示不如MIP、MPR及轴位。

Be careful not to bend his leg at an odd angle.

小心，不要弯曲他的腿在一个多角度。

The system can be widely used in belt weighing and batching process control,etc.

介绍了基于智能模糊控制的嵌入式配料系统的设计方法，对模糊PID控制过程和系统调零作了重点的讨论，同时给出了PID控制的程序流程图和系统定长调零子程序。

"I dunno," she answered,"but if you show me aroun', I'll recognize it from the lighthouse just outside the porthole."

"我不知道，"她回答说，"如果你能带我转转，我能认出来的，因为灯塔就在舷窗外。"