查询词典 maximum

According to the measured pressure data of the four-stroke small utility gasoline engine, the cyclical variations of the maximum pressure, the crank shaft angle at the maximum pressure, the mean indicated pressure and the largest pressure rise rate were analyzed. Meanwhile, the influences of ignition advance angle, load and rotation speed on cyclical variation were also investigated.

根据实测小型通用四冲程汽油机气缸压力，分析了最大爆发压力、最大爆发压力所对应曲轴转角、平均指示压力以及最大压力升高率等参数的循环波动特性，以及点火提前角、负荷和发动机转速对循环波动的影响。

The flood tidal current flows on the whole to the east along the coastline in an anticlockwise rotation with the maximum current velocity over 50cm/s, and the ebb current on the whole to the west with the maximum current velocity under 30cm/s.

海口湾潮流为往复流，涨潮方向基本向东，和岸线走向一致，呈反时针旋转运动，最大流速约50cm/s；落潮方向基本向东，呈顺时针旋转运动，流速小于30cm/s。

The mathematical model was verified in experiment with the method of indirect squeeze cast Archimedean spiral proof sample. And the experimental results show that the maximum deviation between the theoretical value and measured value is less than 8%. This model can be used for quantitative analysis and estimating effects of the craft factors on the filling ability, and can also predict the maximum filling length. It has the important reference value to design the semi-solid alloy rheoforming technology and mould.

采用间接挤压铸造阿基米德螺旋线试样的方法对该数学模型进行了实验验证，实验结果表明：理论计算值与实验测定值之间的最大偏差小于8%；该数学模型可以定量分析和估算工艺因素对充型能力的影响，并可预测充型极限长度，这对半固态合金流变成形工艺设计和模具设计都有参考价值。

Correctional checking formula of melt flow ratio in injection molding was obtained by introducing a correction coefficient β which reflected the complexity degree of mold cavity. The results show that, the maximum flow ratio of 486 can be obtained when injection pressure ranges from 150 MPa to 160 MPa in Archimedes spiral mold for PP, while maximum flow ratio of 419 can be obtained when injection pressure ranges from 160 MPa to 170 MPa for PE. There is a local fluctuation phenomenon for flow ratio and corresponding injection rate in square spiral mold when injection pressure of 100, 120 and 150 MPa for PP and 130, 140 MPa for PE are reached respectively,and this phenomenon is more serious for good fluidity of melt. The average flow ratio in Archimedes spiral mold is 6% larger than that in square spiral mold for PP, and 4% for PE, the average flow ratio of PP is 19% bigger than PE in Archimedes spiral mold, and 15% in square spiral mold. The influence of the cavity profiles on the melt flow ratio is more significant for good fluidity of melt.

研究结果表明：在阿基米德螺旋线模具中，PP在注射压力为150~160 MPa时取得最大流动比485，PE在注射压力为160~170 MPa时取得最大流动比419；在方形螺旋线模具中，PP在注射压力为100，120和150 MPa，PE在注射压力为130和140 MPa时流动比及所对应的注射速率出现波动，且流动性好的熔体波动更为严重；PP在阿基米德螺旋线模具中的流动比均值较其在方形螺旋线模具中大6%，而PE大4%；在阿基米德螺旋线模具中流动比均值PP比PE的流动比均值大19%，而在方形螺旋线模具中PP的流动比均值比PE的大15%；流动性好的熔体受模具型腔轮廓特征影响大。

We discuss asymptotically best linear unbiased estimators of the Logistic population based on selected order statistics and give the formula of computing the ABLUE, the variance and the covariance of the ABLUE in limit, and properties of the ABLUE, and so on. We give the optimum chosen of spacing which is the ABLUE with maximum asymptotic relative efficiency based on complete sample when selected order statistics number is less than 10, and obtain its maximum asymptotic relative efficiency.

讨论基于Logistic总体Ⅱ型截尾样本的若干个样本分位数的总体分布参数的近似最佳线性无偏估计；给出了该近似最佳线性无偏估计的计算公式，估计方差与协方差的极限表达式及估计量的大样本性质等；给出了全样本，样本分位点个数固定，但不超过10情形下，使上述近似最佳线性无偏估计有最大相对联合估计效率时，样本分位数选取法及最大相对联合估计效率；为大样本情形下，该近似最佳线性无偏估计的应用提供了理论依据。

In order to achieve a high concentration and high productivity of exopolysaccharide from Auricularia auricula, the effect of pH on the performance of EPS production in submerged fermentation was investigated. It was showed that the maximum yield of EPS （7.54 g/L） was obtained at pH 5.5, but the mycelial growth rate was enhanced at pH 5.0 and the maximum dry cell weight was

为了实现黑木耳深层发酵生产胞外多糖的高产量和高生产强度的统一，在7L发酵罐中研究不同pH对A.auricula分批发酵生产黑木耳多糖的影响。A.auricula细胞生长的最适pH为5.0，而黑木耳胞外多糖合成的最适pH为5.5。

Maximum output Power This refers to the measure of average power at the maximum power setting.

最大输出功率：指在最大功率设置时的平均功率。

And,the different effects of gene recognition and classification of maximum self-similarity template construction method and averaging along alignment of maximum self-similarity template construction method are also discussed....

对肿瘤基因的识别实验结果表明：基于最大相似度的DP算法能够达到 10 0 %的识别率，本方法可以应用于基因芯片数据的识别、分类和基因疾病推断。

On the basis of the above, comprehensive analyses on the relationship between the moisture content and the maximum compression pressure, maximum compressed density and the power consumption were conducted respectively, having advanced a theoretical basis for the optimum design of the baler.

在此基础上，综合分析含水率与最大压缩力、最大压缩密度和压缩功耗之间的关系，为压缩设备的优化设计提供理论依据。

This technological leadership must be characterized by maximum performance and maximum flexibility.

这种科技领导力必须以最高性能和最高灵活性为特征。

Chimborazo and Cotopaxi, took me by the hand.

越过琴博腊索山和科托帕克西山。

This car is in a good condition.

这辆车的状况很好。