查询词典 maximum error

The arc data interpolation error by secant, tangent and chord, and the smallest error by secant mode is analyzed in this paper. The relation between the maximum radial error and arc radius and approach step-length in the secant mode of arc data interpolation in CNC system is detailed.

在分析数控系统圆弧数据插补割线方式较切线、内接弦插补方式误差更小的基础上，讨论了数控系统圆弧数据插补割线方式中最大径向误差与圆弧半径和逼近步长的关系。

The average error, maximum error and the error standard deviation regarding the test data decrease by 37%(45%), 34%(40%) and 35%(40%), respectively.

对测试数据的平均误差、最大误差和标准差较传统ANFIS分别下降了37%(45%)， 34%(40%)和35%(40%)。

By the method of daily objective analysis and EOF analysis, these reasons of sample leading to big forecasting error are analyzed, the characteristic vector field of maximum temperature、minimum temperature、foehn day and all the big forecasting error day is studied, the result is concluded that the major factor in Shijiazhuang area and its country is hardly same, the foehn effect is the important factor causing forecast error.

进而对温度预报误差较大的样本出现原因进行了逐日客观分析，并通过自然正交函数分解方法，对不同情形下石家庄及周边县站极端最高、最低气温EOF分解特征向量场的变化特征对比，推断出影响石家庄及周边县市气温预报偏差的主要因子大致相同，焚风是导致温度预报出现较大误差的重要原因。

The following conclusions have been made in this paper.(1) Based on CO_2 flux data of eddy covariance, variation characteristics of gross primary productivity in four flux observation stations were studied, which are an alpine meadow, an alpine shrub meadow, a swamp alpine meadow and a steppe alpine meadow at Dongxiong. The results show that photosynthetic capacity of the alpine meadow is the highest, and the annual total GPP is 652.2g C/m~2. Daily-differencing approach is used to analyze the random error of CO_2 fluxes measurements. The results show that the distribution of random error follows more closely follows a double-exponential, rather than a normal distribution, capturing the high peak and thick tail, and the random error varies with environment variables, which violates the assumptions for the ordinary least squares fitting with normality and homoscedasticity, consequently, we introduce maximum likelihood method for parameter optimization.

本文主要在以下几个方面开展工作并获得了一些认知和结论：(1)通过分析样带区域内高寒草甸、高寒灌丛、沼泽化湿地和草原化高寒草甸四个通量观测站点草地生态系统总初级生产力变化特征，研究结果表明HBBT矮嵩草草甸生态系统植被光合作用能力较强，年GPP总量为652.2 gC/m~2，明显高于其他三种生态系统；通过利用"单塔日变化法"获得四站点通量观测数据随机误差，结果表明通量观测随机误差概率分布呈现尖峰厚尾的特征，与正态分布相比，更服从双边指数分布，进一步分析表明通量观测随机误差随环境变量(风速、温度和光合有效辐射)的变化而变化，这违背了普通最小二乘法进行生态过程模型参数优化正态分布且误差同质的假设，因此本研究中引入最大似然法进行生态过程模型参数优化。

Experiment Validation of Hydrodynamics Model of Drum Level The experiment rig was designed, and the experiment equipment was also set up. The experiment results show: As the validation of sloshing period under different levels, maximum error between the results of the experiment and the model is within±10%. As the experiment validation of model under in-and-output flux, changing trends of results of the model and the experiment are consistent, though there is some error in sloshing amplitude, the numeric error is within±20%.

2汽包水位水动力学模型的实验验证设计了实验台架，并建立了实验装置，实验结果表明：就不同水位情况下晃荡周期的验证而言，实验结果与模型计算结果之间的数值误差在±10%以内；就有进出口流量的情况下模型的实验验证而言，模型仿真结果的变化趋势与实验结果基本上是一致的，尽管晃荡幅度和相位上还是存在一定的误差，但其数值误差在±20%以内。

For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the die's whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconventional , unforeseen.

对各类冲模冲件误差在冲模整个寿命中出现的波动、增减趋向及规律等进行全面分析便可发现：冲件误差的主导部分是不变的；因刃口或型腔的自然磨损而出现的误差增量随冲模刃磨冲数增加而使这部分误差逐渐加大；还有部分误差的增量是非常规的、不可预见的。

Because of fault in operation and the precision of instrument,the defect error and accidental error are involved in the procession of data collection,the defect error that are brought by mistakes of people and influence of outside is large,the contingency error that are inevitably and randomicity is little.

在采集数据过程中，由于某些操作或仪器原因，往往使数据中包含人为错误，或外界干扰产生的量值较大的"过失误差"以及不可避免的带随机性质且量值较小的"偶然误差"。

After analyzing the main error sources in the system, it discusses the error separation and error compensation of parts of the error source.

在分析了系统的主要误差源后，本论文重点研究了部分测量误差的分离补偿与修正。

Error analysis of digital instruments on their characteristic parts including sample/holder circuit error and analogue/digital convector error was reviewed in this paper. With the help of some examples and data tables, error origins and the synthetic method were discussed.

评价了数显仪特征部分误差分析方法，包括：采样／保持电路、模数转换单元的误差，并通过典型例子和列表数据分析了多种误差源及其综合计算方法。

Relation between geometrical contour error of inner corner and machining condition is investigated by the experimental plan of Taguchi quality design. Through the quantitative analysis, the geometrical contour error is mainly affected by wire tension and flushing pressure. By regression analysis, a mathematical model is established to estimate cutting path error of corner cutting. According to the estimated cutting path error, the program path is corrected.

研究首先以田口式品质设计实验计画法来探讨加工参数与隅角形状误差间的关系，从变异数分析的结果得知，线张力与冲水压力是对於隅角精度影响最显著因子，应用回归分析建立转角加工路径误差量估测模式，利用此模式以预测不同加工条件下隅角加工路径误差量，依据预测加工路径误差量计算轨迹补偿量，实验结果证明本文所提出轨迹补偿策略可有效提高60%之隅角加工精度。

Fostering the concept of multi-culture firmly and mastering the development of advanced culture correctly are conductive to resisting terrorism, separatism of nationalities and ultraism of religion, which is of great academic theoretical, immediate and profound historical si...

牢固树立多元文化的理念和正确把握先进文化的发展方向，有助于在世界范围内自觉地抵制恐怖主义，民族分裂主义和宗教极端主义。不仅具有重大的学术理论意义，而且也具有重大的现实意义和深远的历史意义。

But if anyone walks in the night, he stumbles, because the light is not in him.

11：10 若在黑夜行走，就必碰跌，因为那光不在他里面。