查询词典 maximum change

On the basis of the above, comprehensive analyses on the relationship between the moisture content and the maximum compression pressure, maximum compressed density and the power consumption were conducted respectively, having advanced a theoretical basis for the optimum design of the baler.

在此基础上，综合分析含水率与最大压缩力、最大压缩密度和压缩功耗之间的关系，为压缩设备的优化设计提供理论依据。

This technological leadership must be characterized by maximum performance and maximum flexibility.

这种科技领导力必须以最高性能和最高灵活性为特征。

After comparison of 30 and 50℃ treatments, AQDS were added into 3 kinds of microorganism biocoenosis from Jiling, Tianjin and Sichuan paddy soil, and it showed that AQDS could accelerate the reduction of Fe 10%-288%, meanwhile, temperature could accelerate the reduction of Fe 6%-17%. In axenic culture treatment of 6 kinds of bacterial strains from Sichuan and Jiangxi paddy soil, the maximum accumulation amount of Fe reduction rate was constant, the maximum reaction rate and ferric reduction rate of ferric strain JX-a08 all increased as temperature rose, which showed that bacterial strain JX-a08 were suitable to 50℃.

在30和50℃培养温度下，来源于吉林、天津和四川的3种水稻土微生物群落添加AQDS可使Fe还原的反应速率常数增加10%~288%，而温度变化的增加幅度仅为6%~17%；对分离自四川和江西水稻土中的6株铁还原菌的纯培养试验发现，菌株JX-a08的Fe最大累积量、还原速率常数、最大反应速率及铁还原率均随培养温度的升高明显增加，表明菌株JX-a08更适于在50℃下生长。

The engine speed at minimum brake specific fuel consumption was happened between maximum engine torque and maximum brake horsepower.

最低燃料消耗率时之引擎转速，落於最大扭力与最大制动马力之间。

Using Latin square test, the effect of geometrical parameters on the characteristics of non-overload sewage pump was studied, and the effecting principle of geometrical parameters on efficiency, maximum brake horsepower and its location were researched, the major and minor factors affecting these performance were found out by way of variance analysis, the correction of equation on maximum brake horsepower and its location were also tested.

用正交试验法研究了各几何参数对无过载排污泵性能的影响，探索了各几何参数对效率、最大轴功率值及其位置的影响规律，并通过方差分析找到了影响这些性能的主要因素和次要因素，验证了无过载排污泵最大轴功率值及其位置公式的正确性，根据试验结果对模型泵提出了进一步设计方案，本试验结果对无过载排污泵水力设计有一定的参考价值。

The main technical parameters of equipment The largest diameter rod into the Φ8mm Diameter round Φ1.20mm-Φ3.5mm The maximum speed cable 25m / s Cable drum diameter Φ450mm Road stretching up to 13 defective Chu-line maximum length of 9m Set-up specifications PND500, PND630 13 die final round adjustable model separate motor

设备主要技术参数最大进杆直径Φ8mm 出线直径Φ1.20mm-Φ3.5mm 最高拉线速度 25m/s 拉线鼓轮直径Φ450mm 最多拉伸道次品 13道储线器最大长度 9m 收线盘规格 PND500，PND630 最终出线模 13模可调。

First, the main technical parameters of equipment The largest diameter rod into the Φ8mm Diameter round Φ2.0mm-Φ3.5mm The maximum speed cable 25m / s Cable drum diameter Φ450mm Road stretching up to 9 defective Chu-line maximum length of 9m Set-up specifications PND500, PND630 Final round 9-mode adjustable model.

一、设备主要技术参数最大进杆直径Φ8mm出线直径Φ2.0mm-Φ3.5mm最高拉线速度 25m/s拉线鼓轮直径Φ450mm最多拉伸道次品 9道储线器最大长度 9m 收线盘规格 PND500，PND630最终出线模 9模可调。

If the temperature control system of the tank is active with the sensing element exposed to vapor, the tank's heating medium may be circulating at maximum rate with the tank wall at maximum temperature.

如果处在蒸汽中的感温元件启动了温度控制系统，储罐的加热介质可能会以最大流量循环，罐壁处在最高温度下。

The relationship between the minimum zone circle, minimum circumscribed circle and maximum inscribed circle was studied. Based on their relationship, the minimum zone circle and minimum circumscribed circle, maximum inscribed circle were transformed mutually.

本文研究了最小区域圆与最小外接圆、最大内接圆特征点的相互关系，实现了最小区域圆与最小外接圆、最大内接圆的相互转化，可有效解决最小区域圆的误差评定。

The some basic methods in composite mechanics are introduced,and relative formulations are derived.Maximum stress criterion,Maximum strain criterion,Hill criterion and Cai-Wu criterion are showed.The solid model of level-stability-panel is built by CATIA software,its finite element model by PATRAN/NASTRAN software.Through finite element analysis,the stresses and displacements of level-stability-panel are obtained.In order to analyze the strength of asingle part of level-stability-panel,the software CLOP is developed.The process of taking the data from NASTRAN's results and importing them to CLOP is showed.The strength of back wall of lev el-stability-panel is calculated by CLOP.

论文叙述了复合材料力学分析的基本方法，并推导了相应的计算公式，给出了几种常用的强度准则；利用CATIA软件对某型直升机的平尾进行实体建模，然后在PATRAN/NASTRAN软件中读入该模型，形成了有限元分析模型，并进行有限元分析，获得了平尾的应力云图和位移云图；为了对平尾的局部复合材料结构进行强度分析，开发了CLOP程序；从平尾结构中取出后樯作为强度分析的对象，表示了从NASTRAN分析的结果到CLOP程序输入的方法，计算出了后樯的强度数据。

The receding calculations and experiment analyses in this subject are built on the blood cast of pig tongue.

本研究课题的前期工作是采用猪舌血管铸型模拟人舌而进行的数值计算与实验分析。

"Each human infection constitutes an opportunity for genetic modification of the virus through reassortment, mutation, or both...."

&每一次人类的感染都暗藏着一次基因修改的机会，无论是通过病毒的整合、突变或者兼而有之。。。。&