查询词典 jig

Taking the important equipment on an automobile wilding line,wilding jig as example,the work piece similarity model is presented based on work piece type,geometric and location information,and then a case database about wilding jig design is established.

以汽车焊接生产线上的关键工艺设备焊接夹具为例，提出以工件类型、几何及定位信息为基础的相似性评价模型，在此基础上建立了夹具设计事例库。

These include the table saw, jig saw, router, doweling jig, clamps, shaper, orbital sander and other tools you may find necessary to use.

这些包括桌锯、夹具锯、路由器、用合板钉钉合的夹具、钳位、成型机、轨道沙磨机和您可以发现必要使用的其他工具。

Because mechanical finger's outflow boundary change has the limitation, this kind of jig may clamp the work piece which takes also correspondingly to have the similar surface, simultaneously as a result of mechanical finger's quantity which installs is limited, but the jig itself does not replace, finger's outflow boundary change was not also big, causes the capture strength not to have the very big compatibility.

由于机械手指的外缘变化具有局限性，这种夹具可以夹取的工件也相应的必须具有类似的表面，同时由于安装的机械手指的数量有限，而夹具本身并不替换，手指的外缘也变化不大，导致了抓取力也不具有很大的适应性。

The topic of this task is:the bottom engine body of D180 8 holes building-block drill and its jig designing,it elaborated the principle of combination drilling machine,the design process,the superiority which compared with the universal engine bed and the ordinary special purpose machine,and carried on the design and the computation to the headstock and the engine bed jig.

本课题题目为：D180柴油机机体底面孔组合钻床及夹具设计。设计过程主要阐述了组合钻床的工作原理，设计过程，与通用机床和普通专用机床相比的优越性，并对其主轴箱和机床夹具进行设计和计算。

The topic of this task is:the bottom engine body of D180 8 holes building-block drill and its jig designing,it elaborated the principle of combination drilling machine,the design process,the superiority which compared with the universal engine bed and the ordinary special purpose machine,and carried on the design and the computation to the headstock and the engine bed jig.

加工工艺毕业设计论文：D180柴油机12孔攻丝机床及夹具设计说明书共55页，22952字，autocad图纸5张摘要本课题题目为：D180柴油机机体底面孔组合钻床及夹具设计。设计过程主要阐述了组合钻床的工作原理，设计过程，与通用机床和普通专用机床相比的优越性，并对其主轴箱和机床夹具进行设计和计算。

Jig drilling units are set up for the location of holes to be machined precision jig fixture at all types of machine tools accounted for the largest proportion.

钻模上均设置钻套，用以被加工孔的位置精度，钻模在各类机床夹具中占的比重最大。

Therefore has designedthe lathe jig, the drilling machine jig.

因此设计了车床夹具、钻床夹具。

Drill holes in the drilling carried out, extending, hinge, screw attack when processing fixture as used in drilling jig, also known as Jig.

在钻床上进行孔的钻，扩，铰，攻螺纹加工时所用的夹具称为钻床夹具，又称钻模。

Generally alluses the drilling machine jig in the volume production, the drillingmachine jig calls 钻模, through drills the set of guidance cuttingtool to carry on the processing to be possible accurately to determinebetween the cutting tool and the work piece relative position, is钻模main characteristic.

在批量生产中一般都采用钻床夹具，钻床夹具又称钻模，通过钻套引导刀具进行加工可准确地确定刀具与工件之间的相对位置，是钻模的主要特点。

During one's term, has completed Japan avionics jig mold, Sanyo Button mold (2 wraps), ohm dragon the key mold altogether four sets of molds decide the material, the design, with the mold, to suppose change, repair the mold work, the JAE jig the quantity produces before leaving job.

在职期间，完成了日本航空电子的夹具模、三洋的Button模具（2套）、欧姆龙的key模具共四套模具的定料、设计、跟模、设变、修模工作，其中JAE的夹具于离职前量产。

Results showed that 0.01g/mL extract of Oxalis corniculata L. had obvious antimicrobial effect on S. aureus, but all extract of Oxalis corniculata L has not any antimicrobial effect on E.

结果表明，0.01g/ml的提取物对摇床培养的金黄色葡萄球菌生长具有明显的抑制作用；但各种浓度的提取物对摇床培养的大肠杆菌生长均无抑制作用。

This will be totally different from Zaro's texture mod, it will be desaturated, dirty etc.

这会和Zaro的那个材质补丁有很大不同，这边是更多的不饱和色，整个都灰扑扑的。