查询词典 injection

The rats were divided into 6 groups and received chitosan embrocation, hyaluronidase injection, hyaluronidase injection plus chitosan embrocation, saline embrocation, or saline injection, or received no treatment as control.

随机分为6组，分别给局部外涂几丁糖、局部注射透明质酸酶、局部注射透明质酸酶联合外涂几丁糖、局部外涂生理盐水、局部注射生理盐水和不进行任何处理。

Methods of stem cell transplantation for acute myocardial infarction included direct epicardium and endocardium injection, intravenous infusion and coronary catheter injection, of which coronary catheter injection was a prospective approach that was direct and with small wound.

干细胞移植治疗急性心肌梗死的方法主要有直接心外膜、心内膜注射、静脉输注和经冠状动脉导管注射4种形式，其中经冠状动脉注射较为直接，创伤小，可能是最有前途的移植途径。

While massage can be slow intramuscular injection or intravenous bolus injection of oxytocin 10U (adding 20ml10%~ 25% glucose fluids), followed by intramuscular or intravenous injection of ergometrine 0.2mg (to fill with those who have heart disease).

在按摩的同时，可肌注或静脉缓慢推注催产素10U(加入20ml10%～25%葡萄糖液内)，继以肌注或静脉推注麦角新碱0.2mg。

The photosensitizer hematoporphyrin derivative was given by two different ways: intraperitoneal injection and intratumoral injection. 630 nm He-Ne laser was used to irradiate the tumor after injection.

以血卟啉衍生物作光敏剂，采用腹腔内和瘤内注射2种不同给药方式，后以波长630 nm的激光照射肿瘤组织，观察PDT后肿瘤体积变化和病理改变。

①postoperative pain after hemorrhoidectomy can be safely and effectively controlled by Acuepoint inject of lappaconitine hydrobromide ②Using the Ashi-points-injection of lappaconitine hydrobromide after hemorrhoidectomy can reduce the pain for a longtime ③Combined with Yaoshu-point-injection can enhance the anaesthetic effect at the day of surgery④The edema at anal margin can be reduced by using of Ashi-points-injection of lappaconitine hydrobromide

①穴位注射氢溴酸高乌甲素对痔术后镇痛是安全而有效的；②术毕时使用氢溴酸高乌甲素阿是穴注射具有术后长效镇痛作用；③联合使用氢溴酸高乌甲素腰俞穴注射可增强手术当天的镇痛效果；④氢溴酸高乌甲素穴位注射具有防止痔术后肛缘水肿的作用。

At the end of this chapter, two computer programs AOGRA_SCE and CINE〓_SCE used for space charge effect calculation are briefly introduced. In Chapter 3, the different injection methods for sector focused cyclotron and the different types of inflectors for axial injection are briefly described firstly. Then the reference particle's orbit and the optical property in spiral inflector, the most common-used injection method, are studied in detail.

在本章的第4节中，介绍了两台强流扇聚焦回旋加速器（50MeV-6mA H〓超导扇聚焦回旋加速器和17MeV-2mA H〓扇聚焦回旋加速器）的具体设计步骤和计算结果，讨论了这两台扇聚焦回旋加速器中加速轨道和相空间的传输以及空间电荷效应的影响。

Through injection, injection allergic lixivium sources, the amount of injection should be less to more, step by step, so that the body's immune function in patients with slowly adapt and fight against allergic source, reaching the ultimate effect of desensitization.

通过打针，注射过敏源的浸出液，注射的量应由少到多，循序渐进，使患者体内的免疫机能慢慢适应并对抗过敏源，达到最终脱敏的效果。

This review summarizes the recent developments of LVI for environmental analysis, include on column injection, programmed temperature vaporizer, AT-column, direct sample introduction/difficult matrix injection, concurrent solvent recondensation large volume splitless injection, and also through oven transfer adsorption desorption interface for on-line connection of LC with CGC.

本文总结了几种常见的LVI，包括柱头进样和程序升温进样，以及近年来发展的一些新技术，如在柱同时溶剂浓缩进样、样品直接引入进样/复杂基质进样和同时溶剂冷凝无分流进样，阐述了各种进样技术的基本原理及其与样品提取、LC纯化在线联用的方法在环境分析应用中的一些最新研究进展。

This paper is designed Pull rod injection mould , discussed the basal principle injection mould, especially Double-surface injection mold design , Have introduced the molding handicraft injecting a mould detailedly、equipment Selection、 feed system、Pulling mechanism and molding part design process, As well as demanded an explanation for mold manufacturing technology, Finally draw out the mould picture by CAD software.

本模具毕业设计主要是设计塑料拔杆的注射模具，论述了注射成型的基本原理，主要是了解模具结构中最基本的两板模的设计，熟悉和掌握模具设计的过程，加深对塑料模具的结构和成型过程的认识。详细介绍了注射模具的成型工艺及设备选择、浇注系统、抽芯机构和成型零部件的设计过程，并对模具制造工艺要求做了说明，最后通过CAD软件绘制出模具图。

The250gL-1 hydrogel was applied in tissue engineering;4weeks after injection,the hard nubble was formed subcutaneously and immatural cartilage was observed.8weeks after injection matural catilage was observed.12weeks after injection the amount of matural cartilage increased.

此水凝胶用于软骨组织工程，注射后4wk在皮下形成稍硬的结节。8wk后形成的结节质地坚韧，切面色泽亮白。

Objective To investigate the effects of interleukin-1 β converting enzyme gene on the biologic characteristics of ovarian cancer cells.

目的 探讨白细胞介素-1 β转换酶的表达，对卵巢癌细胞生物学特性的影响。

Campylobacter: This illness is the most commonly identified cause of diarrheal illness in the world.

弯曲：这种病是最常见的原因查明腹泻病，在世界上。