查询词典 in the course of time

Under these circumstances of course it was no use going to the Court, so the two young men strolled through the village and looked at the old church, and then went and reconnoitered the streams in which they were to fish the next day, and by such means beguiled the time till after seven o'clock.

在这种情况下，当然到庄院去也没有用了，所以两个年轻人便在村子里闲逛，先看看老教堂，然后再踏勘他们第二天要去钓鱼的溪流，他们用这个办法消磨时间，直到七点钟以后。

Before the rank in searching a result leans, the advantage before leaning need not be told, nature is the chance that increases a website to be clicked, very few somebody likes to turn over on 10 a few pages to look for a website, of course, the friend with patient good much time is exceptional, or is you have special objective, for instance: Side girlfriend looks for a very old song, if cannot be found, we part company

的搜索结果中排名靠前，靠前的好处不用讲，自然是增加网站被点击的机会了，很少有人喜欢去翻上10几页去找一个网站吧，当然，耐心好时间多的朋友例外，要么就是你有非凡的目的，比如：帮女朋友找一首很老的歌，假如找不到，咱们就分手

Net valuation, the highest accuracy: the highest rate of domestic accurate real-time valuation of the fund trading system, the net value of the fund known in advance, of course, the decision-making one-upmanship.

净值估值、准确最高：国内准确率最高的基金盘中实时估值系统，提前知晓基金净值，决策当然胜人一筹。

When I'm satisfied with the general volume a shell modifier helps me to give thickness to the piece. In this phase, I don't usually bother that much about every single rivet, hole or cut, I just try to develop a good quad topology of the main volumes. Of course the topology is done by taking count of the main cuts and holes, but the rest can be done easily with a normal or bump map. It's up to you to decide how much a single detail is worth to be modeled or can it be put into a bump map. I usually adopt a "comfortable" criteria...it means that if something looks tricky to me to be carved or extruded into an existing geometry I usually put it into a normal map. When you make something for production, you don't usually have much time to model everything, so you need to set priorities.

当我对整个盔甲的体积感满意之后，一个shell修改器就可以帮我给整个盔甲添加厚度，在这个阶段，我通常不会考虑太多那些细小的铆钉，洞眼或者切边，我只是给整个的模型确立一个好的四边形拓扑结构，当然拓扑是通过重视主要的切割和打洞来形成的，但其余那些细小的部分可以用一个normal 或者bump贴图很容易地模拟出来，这由你来决定到底一个细节是值得建模还是放到一个bump贴图里面，我通常采用一个&舒服&的标准，也就是说，如果有什么东西对我来说，在已有模型上再挤出或者开洞是非常麻烦的，那么我就通过Normal贴图来表现，而当你为商业生产制作模型时，你通常都没有足够的时间来把任何东西都建出来，因此你需要设置重点。

Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.

万寿菊对土壤要求不严，以肥沃。排水良好的砂质壤土为好。

He unstepped the mast and furled the sail and tied it.

他拔下桅杆，把帆卷起，系住。