查询词典 friction coefficient

Main innovation and study achievements are described as follows:(1) A set of friction noise testing system was set up on the pin-on tester. In the process of friction testing in which the TRIP steel with transformation characteristics is continuously sliding in unilateralism, variety rule of the friction noise intensity was studied.

本文的主要创新和研究成果体现在以下方面：(1)在销盘摩擦磨损试验机上建立了一套摩擦噪声测试系统，研究了具有相变特征的TRIP钢在单向连续滑动的摩擦试验过程中，摩擦噪声的强度的变化规律。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

At the aspect of the fade and the average wear, the bakelite modified by the chemigum was better than the bakelite modified by the bunas; When mixing the kevlar fiber and steel fiber their"cooperation effect"happened easily, especially, in the proportion of one to four, the friction materials had the better tribology performance; It was demonstrated that Sb2S3 played a role of binding adhesive of friction materials in high temperature, which could reduce the content of the agglomerant, but it was a higher price material, mixing the petroleum powder and CuS in appropriate proportion would replace it in friction

应用造粒技术，采用颗粒包层的方法，改变摩擦材料内部结构，使摩擦材料由配方比例设计到配方与结构综合设计的转变成为可能，将为研制新型摩擦材料探索出一条新的思路。

The results showed that under the given experimental conditions,the surface layer with richiron and poor copper was formed in the surface worn region of the semimetallic friction material,the depth of organic ingredient pyrolysis caused by friction heat in worn surfaces was atout 0.35mm; the semimetallic friction material containing 15%-20%of Cu had better wear-resistance,and can form a even and continuous transfer film of copper; crack peeling was the importantmechanism of the counterpart.

半金属摩擦材料具有摩擦系数稳定，耐磨性好，对环境污染小和对偶件表面损伤小等优点，但其在摩擦热和界面应力等因素作用下，表层会发生弹性变形，塑性变形，元素扩散，组分转移和摩擦化学反应等现象，因此，利用扫描电子显微镜X射线能量色散谱和差热－热重分析，对铜纤维增强的半金属摩擦材料与灰铸铁滑动摩擦表面层的特性作了分析研究，考察了表面层特性对摩擦损行为的影响。

Under heavy load and high temperature conditions, the nanoparticles are flatted between two friction surfaces and form a sliding system which makes the friction surface more flat to reduce the friction factor and the wear value.

在重载和高温条件下，纳米粒子平铺在摩擦面之间形成滑动摩擦层，以降低摩擦表面的摩擦因数和磨斑直径。

At present, the company mainly produces clutch friction plate motorcycle, engineering machinery brakes, motor friction films, mower, broken sticks machine, automobile air conditioning compressor, electric hoist, etc. special friction material.

目前，公司主要生产摩托车离合器摩擦片，工程机械用刹车片、电机摩擦片，割草机、碎枝机、汽车空调压缩机、电动葫芦机等特种摩擦材料。

The operation of the shaft and the sliding friction between the axle seat into a rolling friction, thus reducing the friction loss of a precision mechanical components, called the rolling bearing.

将运转的轴与轴座之间的滑动摩擦变为滚动摩擦，从而减少摩擦损失的一种精密的机械元件，叫滚动轴承。

The effect of temperature on the friction and wear performances of multi-fibers reinforced automotive brake is investigated using XD-MSM tester. The mechanism of friction and wear is analyzed by observing the surfaces of friction material worn at different temperatures by means of scanning electron microscope.

利用XD-MSM型定速摩擦试验机，考察了摩擦材料的摩擦系数和磨损率随温度变化的情况，并且通过扫描电镜观察了摩擦材料在不同温度下磨损后的表面形貌，分析其摩擦磨损机理。

Its friction type clutch working principle is when power transmits the export and input end design on route have is active and driven move two pieces of friction plate, the conduct that passes through the combination of friction plate to control power and cut off.

摩擦式离合器其工作原理是在动力传递路线上的输出和输入端设计有主动和从动两块摩擦盘，通过摩擦盘的结合来控制动力的传导和切断。

After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

He tendered his resignation to the Prime Minister.

他向首相递了辞呈。不适合

International economy and trade,Nanking 210044

国际经济与贸易，南京 210044