查询词典 force

This test indicates that using bicortical screws in the first and third hole of the proximal end of the LISS is the best way for treating distal femur fractures AO/33-A3, it can not only reach the best balance and it create the biggest force to resist torsional force, but also decrease the shearing force, torsional force so as to prevent hardware failure.

采用LISS钢板治疗股骨远端33-A3型骨折时，骨折近端螺钉第1、3孔双皮质固定在钢板、螺钉的固定平衡性及对抗扭转拔出方面明显优于其他各试验组，能够有效地降低钢板、螺钉与骨质之间的剪切力和扭转力，从而防止螺钉、钢板早期松动脱落。

It showed that the flow regime and the forces were closely related to each other.Calculation indicated that the interfacial tension force, static pressure force, viscous drag force and dynamic lift force were the main forces acting on the droplets. The formation process of the droplet was studied.

在一定条件下计算了液滴所受的力，结果表明，表面张力引起的力、液滴内外静压差产生的力、平行于膜表面的流动曳力和运动浮力是主要的力；在此基础上，探讨了液滴的形成过程。

Dynamic cutting force is a basic parameter and it directly influences relative displacement between tool and workpiece, tool wear and surface quality in turning operation. Therefore, simulation model of dynamic cutting force is an important part of machining physical simulation research. Cutting force models commonly used are empiristic equations. These equations are often based on statistical analysis of machining data, obtained via changing one or more machining parameters, whilst fixing others. But a complete turning process and nature of force can not be accurately described by means of these models.

动态切削力是切削加工过程中的基本参数，其动态变化直接影响加工过程中刀具与工件的相对位移、刀具磨损和表面加工质量等，因此动态切削力的预测仿真建模是切削过程物理仿真研究的基础，但是目前大多使用经验公式描述动态切削力，这些经验公式多少存在一些不足，难以完全真实地反映在整个切削过程中力的变化历程和变化特点。

And we consider that the firm's labor force allocation mode in our country following an evolutionary process. Its progress is from depending on low-grade and methodic state firm's interior labor force market to out-of-order firm's labor force market which is made up of state, private and foreign firms. And it is possible self-organizing to depending on high-grade and methodic firm's interior and exterior labor force market.

首先，本文运用演化动力学中的耗散结构和自组织理论，对二十多年来我国企业的劳动力配置方式进行了演化分析，认为我国的企业劳动力配置方式是从依靠低级有序的国有企业内部劳动力市场到由依靠国有企业、私营企业、外资企业等组成的无序企业劳动力市场的演化过程，它将有可能自组织发展到依靠高级有序的企业内部劳动力市场和企业外部劳动力市场。

The basic study content of this essay is follow as:1.To calculate the stable factor k_i~0 of individual slices according to self-forced condition of slices,under the condition of without inter-slices force.2.To calculate transferal force R_i, stabile factor K_i of individual slices and stabile factor K of the stable slope, under the condition of there is a level transferal force between slices and the slope is stable. If the slope is not stable, to calculate the transferal force R_i between individual slices, the stabile factor K_i of individual slices and the stable factor K of the unstable slope in term of concordant conditions of acceleration.

本文研究的基本内容包括： 1、研究土条条间不传递力情况下，由土条自受力状态计算各土条的稳定系数K_i，并由K_i计算稳定土坡的稳定系数K； 2、研究条间传递水平力情况下，若土坡稳定，由土条预平衡状态、传力顺序和传力边界条件，推导各土条间的水平传力R_i的理论公式和各土条的稳定系数K_i，并由K_i计算稳定土坡的稳定系数K；若土坡失稳，由加速度和谐条件计算各土条间的水平传力R_i和各土条的稳定系数K_i，并由K_i计算失稳土坡的稳定系数K

While with the Coriolis force omitted, the flow in the cavity is under the influence of centrifugal buoyancy force, which can develop from stable to unstable as this force enhances. The centrifugal buoyancy force could lead to flow unstably.

哥氏力垂直于〓与〓构成的平面，对径向速度导致切向作用力，对切向速度导致径向作用力，在该力的作用下盘腔内轴向通流诱导的旋涡被压扁，尽管涡强有所增加，但是盘面的平均换热基本减弱。

Safety Belt Force Limit Furling Device: In order to avoid the accident to the aged people and children caused by the force of collision on the safety belt, the force limit furling device will take effect when it exceeds the certain limit of the tension force (450-650kg), make the core of furling devicehave several rolls on the axis, to pull out several of it.

安全带限力卷收器：为了避免撞击时承受普通安全带的力过大而造成对老弱和年幼者的意外伤害；限力卷收器在织带收紧力超过一定限度（一般设定为450-650KG）时开始作用，使卷收器芯轴旋转数圈，从而使织带拉出少许。

Safety Belt Force Limit Furling Device: In order to avoid the accident to the aged people and children caused by the force of collision on the safety belt, the force limit furling device will take effect when it exceeds the certain limit of the tension force (450-650kg), make the core of furling device have several rolls on the axis, to pull out several of it.

安全带限力卷收器：为了避免撞击时承受普通安全带的力过大而造成对老弱和年幼者的意外伤害；限力卷收器在织带收紧力超过一定限度（一般设定为450-650KG）时开始作用，使卷收器芯轴旋转数圈，从而使织带拉出少许。

To ensure, therefore, our future force does not encounter a situation in which it is overmatched by an enemy force, we must conduct a thorough force-on-force analysis of potential future opponents.

因此为了确保我们未来部队不会处於敌人占优势的境地，我们必须对潜在的对手进行全面的部队-部队分析。

Fourteen phalanxes on feet are composed of the army, navy, air force and the Second Artillery Force of the People"s Liberation Army, the People"s Armed Police Force and reserved force.

十四个徒步方阵队由陆军、海军、空军和二炮、武警和后备役部队组成。

But in the course of internationalization, they meet with misunderstanding and puzzlement.

许多企业已经意识到了这一点，但在国际化的进程中，仍存在一些误区与困惑。

Inorder toaccomplish this goal as quickly as possible, we'll beteamingup with anexperienced group of modelers, skinners, and animatorswhosenames willbe announced in the coming weeks.

为了尽快实现这个目标，我们在未来数周内将公布与一些有经验的模型、皮肤、动画制作小组合作。