查询词典 flash butt welding

According to characteristics of thin strip cold rolling product line,the total configuration and control system of special flash butt welding machine in thin strip cold rolling was designed.

针对冷政薄钢板生产的特点，设计了冷轧薄钢板专用闪光焊机的总体结构。

Simulation of DC flash butt welding by coupling with electricity, heat, and mechanics will be instrumental in designing and drawing out technical specification.

本文首先采用有限元模拟方法对超细晶粒钢直流电阻闪光对焊的焊接过程进行了研究，建立了直流电阻闪光对焊过程的电、热、力耦合模型。

The steel is provided with the characteristics of ultra fine grain and ultra purity, so the result has the excellent mechanical properties with combination of strength and toughness. DC flash butt welding is a kind of solid joining method with high efficiency. The micro characteristics of HAZ affect the weld joints greatly.

直流电阻闪光对焊是一种高效的固态连接方法，其焊接热影响区的显微特性对焊接接头的性能有着重要的影响，由于这种方法与熔化焊具有本质的区别，所以对超细晶粒钢的闪光对焊焊接适用性研究会有助于推进新一代钢铁材料的研究和应用开发。

An interface between controller and hydraulic system was designed in Simulink and AMESim, by which the eletro-hydraulic co-simulation was achieved. The result shows that the forecast controller exhibits excellent performance on eliminating synchronism of upsetting force in flash butt welding.

仿真模型中建立了AMESim软件和Simulink软件的通信接口，通过这个接口实现了基于AMESim/Simulink的电液联合仿真；仿真结果表明基于单神经元预测控制的同步误差调节器在消除顶锻阶段同步误差上具有明显的作用。

UN-25, 75 , 100-type flash method used for welding low carbon steel and non-ferrous metal butt parts.

UN-25、75、100型对焊机采用闪光法对接低碳钢及有色金属零件。

1 When thickness of the short pitch or long neck flange straight side of Type B doesn't equal to the cylinder thickness connected with it: If cylinder thickness is not larger than 10mm, and thickness difference with short pitch or long neck straight side is larger than 3mm; If cylinder thickness is larger than 10mm, and thickness difference with short pitch or long neck straight side is larger than 30% of the cylinder thickness or 5mm, Type B flange should take the slope value 1: 3, and the long neck flange should be thinned according to Chart 1, or have pile welding on the end of butt welding seam to achieve transition.

6.5.1 乙型法兰的短节厚度或长颈法兰的直边厚度与其相联接的圆筒厚度不等时：若圆筒厚度不大于10mm，且与短节或长颈直边厚度差超过3mm；若圆筒厚度大于10mm，且与短节或长颈直边厚度差大于圆筒厚度的30%或超过5mm时，乙型平焊法兰应按斜率1：3，长颈对焊法兰按图1虚线削薄，或者在对接焊缝的筒体端部按图2堆焊过渡。

The welding process of the butt welding machine used to weld bicycle joints employs a cam transmission mechanism. Its procedure is decided by the contour of the cam.

自行车接头对焊机焊接过程的进行采用凸轮机构控制，焊接过程由凸轮的外廓形状所决定。

Provide welding neck flange butt welding required for the purpose of the right pad with neighboring component.

提供焊接法兰的脖子上对接焊目的所需要的正确垫与邻近组成部分。

It is feasible to replace lap welding with butt welding to improve quality of mid-diameter spiral weld pipe.

用高频对接焊代替高频搭接焊是提高中直径螺旋焊管质量的可靠途径。

The series welding machines get the optimal design. To be the same with multi-measure and different materials butt welding.

本系列焊机结构设计合理，适用于多种规格尺寸及不同材质的对接。

There had been a moment during the breakfast meeting, though, after the backslapping and the small talk and when all of us were seated, with Vice President Cheney eating his eggs Benedict impassively and Karl Rove at the far end of the table discreetly checking his BlackBerry, that I witnessed a different side of the man.

那次早餐会期间，在表示过关心和寒暄以后，我们所有人坐了下来，我注意观察了一下，副总统切尼面无表情地吃着班尼迪克蛋（Eggs benedict，源自美国，以英式松饼、火腿、水煮蛋以及荷兰酱组合而成），卡尔。罗夫在餐桌的远端谨慎地经常查看他的黑莓手机，我目睹了他所不为人知的一面。

Talk Undelete failed; someone else may have undeleted the page first.

Talk 无法删除选定的页面或图像（它可能已经被其他人删除了）。