查询词典 finit element method

Based 188F gasoline engine heat load studies, the research unit based on Using AutoCAD software for the design cylinder sleeve, and then use the software PRO-E 3D modeling, and the calculated and experimental analysis to determine the reference cylinder heat transfer across borders, reuse finite element analysis software ANSYS right cylinder mathematical analysis, systematically on the finite element method in 188F cylinder gasoline engine design of the application, in-depth study of the thermal load on the performance and reliability, as relates to structural strength, stiffness, temperature and so on.

本文以188F汽油机热负荷为研究对象，在研究整机的基础上，利用AUTOCAD软件进行汽缸套的设计，然后用PRO-E软件进行三维建模，并通过计算解析和实验参考确定了气缸套各处的传热边界条件，再利用有限元分析软件ANSYS对气缸套进行数学分析，系统地探讨了有限元法在188F汽油机缸套设计中的应用，深入研究了其热负荷对性能和可靠性的影响，内容涉及到结构强度、刚度、温度场等方面。

In view of the questions in theoretic analysis and numerical simulation with the finite element method,the separation criterion of chips, the surface contact, the setting of friction coefficient,and the thermal stress coupling are researched. A simulation example is presented by applying the finite element analysis software-ANSYS,and the change of stress and strain in metal cutting process, the forming of shear plane and the influence of the temperature field on metal cutting are analyzed. The tool's strength is also analyzed.

基于理论分析和实际有限元数值模拟计算中遇到的问题，研究、讨论了切屑分离标准、表面接触、摩擦系数的设定、切屑与工件之间的连接以及热应力耦合分析等各项技术，并应用大型有限元分析软件ANSYS，具体分析了金属切削过程中应力和应变的变化、剪切面的形成以及温度场对金属切削的影响，并依此对刀具作强度分析，得到若干结论。

The characteristic of this model is:a new interface edge singular element model is derived based on the numerical fundamental solutions obtained from the finite element eigensolutions method.

该模型的独特之处在于：基于有限元特征法得到的奇异性场数值特征解建立了一种新型界面端奇异单元。

The ATF method is also applied to develop singular element in the V-notch analysis and an element with notch named ATF-VN is formulated.

采用解析试函数法构造了含切口单元ATF-VN。用此单元分析切口问题也非常有效。

Based on the deep analysis of finite element method and process characteristics of tube stagger spinning, through further development of the general FEM software-MSC/MARC, the three dimension plastic-elastic finite element model is founded.

本文在对有限元基本理论和筒形件错距旋压工艺特点进行深入分析的基础上，通过基于MSC／MARC的二次开发，建立了筒形件错距旋压的三维弹塑性有限元模型。

According to structural characteristics of floating slab tracks, a track segment element was taken between two adjacent fasteners. For each element, rails were regarded as Euler beams supported by discrete viscoelastic supports. The fasteners and rubber supports were replaced by a linear spring and damp. So the vibration model of the floating slab track was established. In constructing vibration model of a metro train, each car of the metro train with two suspensions was modeled as a multi-rigid body system, in which rigid bodies were connected with each other by a linear spring and damp. Combining the potential energy of vertical vibration of the track with that of the metro train, the total potential energy of vertical vibration of the train and track was obtained. And then, the matrix equation of vertical vibration of the system was established using the principle of total potential energy with stationary value in elastic system dynamics and the "set-in-right-position" rule for formulating system matrices. The vibration responses of the system can be obtained by solving the matrix equation with the direct time integration such as Wilson-θ method.

摘 要：针对浮置板式轨道结构特点，取相邻2个扣件之间的轨道为1个轨段单元，钢轨视为连续弹性点支承Euler梁，浮置板视为弹性薄板，扣件系统及橡胶支座均模拟为线性弹簧及粘滞阻尼器，建立浮置板式轨道振动模型；将城轨列车中的车辆均离散为多刚体系统，各刚体之间通过线性弹簧及粘滞阻尼器相连，建立列车振动模型；将浮置板式轨道及列车振动势能叠加，得到系统竖向振动总势能；基于弹性系统动力学总势能不变值原理及形成系统矩阵的"对号入座"法则，建立此系统竖向振动矩阵方程；采用Wilson-θ逐步积分法求解此矩阵方程，得出此系统竖向振动响应。

A statistical optimization method for the design of a fluorinated polyimide wavelength division element for optical communications is proposed. The optimized device is an interleaver element suitable for dividing over 40 wavelengths in the 1550 nm band.

提出并采用统计优化的设计方法解决含氟聚酰亚胺波导波长交叉分离耦合器的偏振态变动的影响。

Commencing from the character analysis of overall stiffness matrix of finite element method, the author brings forward it which is important to realize full nonzero memory of overall stiffness matrix, obtains correlative interlink of nodal point from analyzing affiliated element of nodal point, conforms every submatrix's position in overall stiffness matrix, realizes full nonzero memory of overall stiffness matrix.

论文根据面向对象程序设计的特点，建立了有限元模型的相关类，给出了基本的程序设计框架。

The first method used not only the row element but also the column element of covariance matrix to structure a toeplitz matrix; this process accomplishes the function of forward/backward spatial smoothing for multipath signals.

第一种改进的方法不但利用了阵列输出协方差矩阵的行元素，而且还利用了阵列输出协方差矩阵的列元素构造Toeplitz矩阵，实现了前、后向空间平滑解相干的功能。

Load or create object from "name" field, save to local call Name unmarshalling method store reference from local variable to "name" field unmarshal "street1" field value from "street" element unmarshal "city" field value from "city" element ...

清单 4 为图 2 的左下部分给出了实现从 XML 到 Java 对象的解编排所需的抽象操作列表。清单的顶端部分完成的是一个 Customer 实例的解编排，底部完成的是一个 Name 实例的解编排。

A strange and mysterious deep sea creature.

一种奇异、神秘的深海生物。

It's a yellow rectangle .

这是黄色的长方形。