查询词典 filler

In the dissertation, a new stabilization method, equal-density method was adopted to prepare modified asphalts with storage stability at high temperature. In this method, a compound was prepared by premixing polymer and filler, and the compound was mixed with asphalt to prepare Polymer-Modified Asphalt by changing the ratio of polymer and filler. The asphalts with good storage stability were formed with the addition of filler, by regulating the density difference between polymer and asphalt. With identifying the effect of composition factor and the technique conditions on mechanical properties of polymer/filler compound and the molecular distribution of the polymer, identifying the effect of composition factor and the technique conditions on the properties and structure of polymer/filler modified asphalt, Styrene-Butadiene-Styrene copolymer, Low Density PolyEthylene, Styrene-Ethylene-Butadiene-Styrene block copolymer modified asphalts with good storage stability and performance were prepared. Rheological method, gel content analysis and swelling measurement were adopted to elucidate the interaction between the polymer and filler. Filler reduced the difference between the polymer and asphalt with the premixing technique, which led to the improvement of the storage stability of the modified asphalts. The thermo-oxidative aging process of base asphalt and PMA were studied and the effect of antioxidant additives on the base asphalt and PMA were analyzed.

本论文采用等密度方法，即预先混合聚合物与填料制备复合物，复合物在沥青中会吸收油份而溶胀，改变填料的用量从而调节聚合物与沥青的密度差异的方法，制备出高温贮存稳定的改性沥青，并研究了工艺条件和配方因素对聚合物/填料复合物力学和聚合物分子量分布的影响，系统考察了工艺条件和配方因素对聚合物/填料改性沥青性能与形态结构的影响，研制出性能优良、高温贮存稳定的苯乙烯-丁二烯-苯乙烯三嵌段共聚物、氢化SBS、低密度聚乙烯改性沥青，并通过流变学分析方法及凝胶和溶胀测试探讨了聚合物与填料的相互作用，指出经过预混工艺填料改变了聚合物与沥青的密度差异，以此说明聚合物/填料改性沥青高温贮存稳定的原因；研究了基质沥青和聚合物改性沥青热氧老化过程，并分析了抗氧剂对基质沥青及聚合物改性沥青的影响，探讨了抗氧剂提高沥青耐老化性能的原因。

The research on bound rubber and reinforcing effect of mineral filler showed that there are four kind of interactions between filler and rubber matrix in uncured mix The unbounded rubber on the surface of filler will solve in organic solvent The rubber bounded by stronger physical or chemical interaction with filler will dissolve in organic solvent The bound rubber on the surface of filler by different extent acid-base interactions will solve in basic organic solvent The bound rubber on the surface of filler by chemical action (no acid-base type) will dissolve in basic organic solvent

结合橡胶和增强作用的研究表明，在混炼胶中，硅橡胶与矿物填料的作用形式有四种。没有联结在矿物表面的非结合橡胶和仅靠物理吸附联结在填料表面的硅橡胶将溶解于有机溶剂；与填料有较强相互作用的硅橡胶不溶于有机溶剂；通过不同层次的酸碱作用联接在矿物表面的硅橡胶将溶解于碱性有机溶剂；与填料有牢固化学结合的硅橡胶不溶于碱性有机溶剂。

The results show that the spreading area of series Ni-P filler metal increases with the increase of brazing temperature, and the spreading areas of Ni-P filler metal is larger than that of Ni-Cr-P filler metal; the shear strength of the brazed joint at room temperature increases with the increase of temperature from 925℃ to 1000℃, and the shear strength of the stainless steel joint brazed with Ni-P filler metal is superior to that with Ni-Cr-P filler metal by 30~40 MPa in the same brazing technology.

结果表明，Ni-P系钎料铺展面积随钎焊温度的升高而增大，并且相同温度下不含Cr的Ni-P钎料铺展面积大于Ni-Cr-P的铺展面积；钎焊温度从925 ℃升高到1000 ℃过程中，Ni-P、Ni-Cr-P钎料钎焊不锈钢接头的室温剪切强度均增大，并且在相同钎焊工艺下，不含Cr的Ni-P钎料钎焊不锈钢接头室温剪切强度优于Ni-Cr-P钎焊接头强度30~40 MPa；Ni-P系钎料钎焊接头高温强度随温度升高而下降，测试温度超过500 ℃时，相同温度下含Cr的钎料能够提高钎焊接头强度0~30 MPa。

The mechanical properties and microstructure of the joints joined by the new developed filler metal and TC18 filler metal were compared,the results showed that only the strength of the joint joined by TC18 filler metal was satisfied,while the comprehensive mechanical properties of the joint joined by the developed filler wire were ideal.

对采用研制的焊丝和采用TC18同质焊材钨极氩弧焊焊接TC18钛合金的接头力学性能及微观组织进行了对比研究，结果表明：采用同质焊材焊接TC18钛合金只能保证接头的强度指标，而采用研制的新型焊丝焊接TC18钛合金，可以保证接头具有优良的综合力学性能。

Two Mode Carrueau Viscosity model showed that polymer and filler had a strong effect on structure orientation, demonstrating that the interaction between polymer and filler in premixing them existed, and the interaction made the polymer and the filler gather in blending the polymer/filler compound with asphalt.

老化使得沥青的软化点及粘度增大，而针入度和延度降低，在红外谱图上主要表现为羰基峰的增大，而亚砜基峰的变化趋势和老化时间及强度相关，老化之初亚砜基峰增大，但随后又减少。

To install the fixed filler on the corner cabinet, use a ф4.2MM drill to drill a hole on the bottom panel at a place near the fixed filler. Use pneumatic screwdriver to turn at the hole positions to form countersink holes. Use 4*50 self-tapping screws to secure the fixed filler on the bottom panel. Keep

转角柜固定封板的安装，先用ф4.2MM的直钻在柜底板靠近固定封板处打孔，/然后用风批头在打孔处转动几下形成螺钉沉孔，再用4*50的自功钉把封板固定在柜底板上/安装可调脚将柜底保持朝上，然后正面进入50MM画线并装好柜脚座。

The high density printing and dyeing, the "TB/TA、TB/TH swing the filler freely" applied in the craft of anaerobic hydrolysis in the chemical engineering waste water, this research for the effectiveness of filler optimization was through small and middle sized testing. The fruitage of the study could be used to the selection of filler and application of practical significance in guiding the project.

高浓度印染、化工废水厌氧水解工艺中所应用的"TB/TA、TB/TH自由摆动填料"，通过小试、中试实验对多种填料进行效能优化研究，该实验结果对填料的选型及实际工程，特别是在成分复杂多变的印染、化工废水处理工程中的应用具有重要的指导意义。

This difference was indistinctive at a higher filler content. This is because there existed a critical content for naoscale filler, which determined the agglomeration or not of the nanoscale filler in the polymer matrix.

其原因在于纳米粒子的填充存在着临界含量问题，高于临界含量，部分纳米粒子将不可避免的发生团聚；低于临界含量，纳米粒子与聚合物颗粒能充分的共混，此时纳米粒子的尺寸效应才能充分表现出来。

The structure of uncured mix and vulcanite, physical and chemical interaction between filler and matrix, mechanical property of composites were investigated It was found and explained that the compact relationship among bound rubber, cross-linkage density and physical property in mineral filler/silicone rubber composite In detail, BR〓, D〓(cross-linkage density using basic solvent as swell liquid) and module have direct relationship, because they all show chemical interaction between filler and matrix from different angles, respectively BR〓(bound rubber in toluene solvent), D〓(cross-linkage density using toluene solvent as swell liquid) and tensile strength have compact relationship also, because they all show total interaction from different angles, respectively

研究了未硫化胶和硫化胶的结构、填料与基体的物理化学作用、及这些结构和作用的表现形式，发现和解释矿物填料/硅橡胶复合材料中结合橡胶、交联密度与复合材料的力学性能密切关系。具体说，BR〓、D〓和弹性模量均从某个侧面反映复合材料中填料与基体间的化学作用，三者的关系比较密切：BR〓、D〓和抗拉强度均反映复合材料中填料与基体间总体相互作用，三者的关系比较密切。

0 OBR field definitions OBR 字段定义 The daggered items in this segment are not created by the placer known to the filler, not the placer. They are created by the filler and valued as needed when the OBR segment is returned as part of a report. Hence on a new order sent to the filler, they are not valued.

段中加剑号的项不是由执行者认识的下医嘱人传送的，也不是下医嘱者传送的，而是由执行者传送，在 OBR 作为报告的一部分出现时，加剑号的项就是必要的，因此在给执行者传送新医嘱时，此项是空的。

In the chapter 2, the theoretic knowledge about the photosensitive resin and the grinding tools was firstly introduced.

第二章阐述了光固化树脂结合剂磨具的相关理论研究。

Do not use the program's indenting or margin-setting features; these will be added during typesetting.

不要使用缩排，页面边缘设置之类的选项，偶看不大懂。