查询词典 dynamic friction

As the results, both the friction and wear are much lower in n-monohydric alcohols than in water; in ethanol, the friction and wear increase rapidly when a small amount of water was blended into the lubricant; the friction and wear decrease slightly with increasing the chain length in n-alcohols; in polyhydric alcohols, the increase of the hydroxyl number greatly reduces the friction and wear.

研究结果表明，陶瓷在醇中的摩擦和磨损均比水中低；在乙醇中加入少量水可明显增大其摩擦和磨损；随着一元醇分子链长的增加，其摩擦磨损略有降低；多元醇中羟基数目越多，其摩擦磨损越低。

The friction factor of glass reinforced plastic mortar pipe and typical soil of Shanghai, the develop characters of friction and the effect of injecting slurry on the frictional characters are got through the experiments. The result shows: the ektexine of glass reinforced plastic mortar pipe is slipperier than concrete pipe; injecting slurry could minish the friction between soil and pipe, but the effect of minishing friction is bear

然后通过对玻璃钢夹砂顶管进行摩阻力特性整管试验与直剪试验研究，得到了玻璃钢夹砂顶管外壁、混凝土与上海地区典型土层间的摩擦系数，以及玻璃钢夹砂顶管外壁摩阻力的发展特性，并且分析了注浆

Introduce the cohesion-friction model of rock strength theory, and extend the model to select the strength of sliding plane, discuss the variation rules of peak strength and residual strength under different normal stress, and then present the selection model of shearing strength. After the result of cohesion-friction model is compared with Coulomb Criterion, it is found that when the results of shearing strength are many and adjacent the strength parameters can not be regressed by least square method, instead the results should be divided into some beelines at that time according to the cohesion-friction model.(4) Discuss the characters of hard structural plane and weak structural plane: The adhesive friction theory is applied to research the changing course of shear area of hard structural plane and its influence on shear stress.

3介绍了岩石强度理论中的粘接摩擦模型，运用此模型分析依附型滑动面的演化过程，并将其推广到边坡岩土体抗剪强度的选取，讨论了不同法向应力下峰值强度和残余强度随法向应力的变化规律，在此基础上给出抗剪强度的选取模式，讨论了对实际取值结果的影响，并与传统的Coulomb准则进行了比较分析，指出直剪试验的法向应力在小应力区的点较多且抗剪强度结果差异不大时，不宜直接运用最小二乘法回归抗剪强度参数，此时应结合粘接摩擦模型对结果进行线性分段。

All the actuators of the three-axis turntable are brushless torque motors, all the bearings are aerostatic air bearings, so the friction caused by these elements can be neglected. The main source of friction is the metal-to-metal friction on the slip rings. Hence the "Columb+Viscous+Static" friction model is used here for analysis.

由于三轴转台的驱动系统选用的是无刷电机，轴承则采用的是气浮轴承，轴系上的摩擦力已大大降低，三轴转台上的摩擦主要是滑环轴上金属对金属的摩擦，所以文中选用&库仑＋粘滞＋静摩擦&的摩擦模型来进行分析。

Because the error mainly comes from theresonant region, the error correction method can only be used in resonant region, andcan effectively improve the efficiency of the statistical analyzing solutions. Two types of the mistuned bladed disks, whose friction damping are blade dryfriction damping and blade-to-blade dry friction damping, are modeled respectively. Amulti-harmonic method which can employ the fast Fourier transformationtechnique is proposed to investigate the vibratory response of the bladed disks withthese two types of nonlinear friction damping. Formulations of the solution for thesetwo types of motion functions are deduced. The characteristics of the forced responseof the bladed disks with these two dry friction damping are analyzed and summarizedunder various system parameters. The vibratory response of the bladed disk with dryfriction scatter mistuning is investigated.

针对叶盘系统中两类主要的非线性干摩擦阻尼形式，分别建立了具有叶片干摩擦阻尼和叶间干摩擦阻尼的失谐叶盘系统的非线性力学模型；提出了一种可利用快速傅立叶变换技术的多谐波分析方法；分别推导了具有这两类干摩擦阻尼形式的叶盘系统运动方程的求解公式；在各种系统参数条件下，研究了干摩擦阻尼失谐叶盘系统的受迫振动响应特性；对具有干摩擦散乱失谐的叶盘系统振动响应进行了研究，分析总结了干摩擦散乱失谐对叶盘系统振动响应特性的特殊影响规律。

The main products include: 1, tensile strength, universal testing machine: microcomputer-controlled universal testing machine, economic-type universal testing machine, tensile testing machine micro-computer, electric / manual (Vertical / Horizontal / double pole / single pole) Rally Units, micro-computer plug test machine, spring tension and compression testing machine, etc.; Second, environmental testing machine series: constant temperature and humidity chamber, drying oven, large load-aging room, walk-in constant temperature and humidity test chamber , Thermal Shock Test Chamber, UV weathering tester, salt spray testing machine, aging chamber three, cartons, packaging, furniture testing machine series: microcomputer carton compression testing machine, the breakdown strength test machine, drop (single arm / arms) Test Units, Units microcomputer vibration test, vibration test Analog Motor Transport Units four, electrical equipment testing machine series: plug wire bending test machine, drum testing machine plugs, plug wire hoist swing test machine, plug-line static tensile testing machine, sudden pull test machine, power cord bending test machine, combustion testing machine, 90-degree peel strength testing machine, torsion testing machine wire, wire abrasion test machine, flexible wires and flexibility testing machine, wire print Kennedy fastness testing machine, measuring the rate of wire testing machine, fatigue test handset line stretching machine, plug test machine, torsion testing machine cold, temperature testing machine, wire thermostat ball pressure testing machine, hot wire tester, leakage from marks tester, wire short-circuit / open circuit / high pressure / low pressure / insulation / conduction / mispairing tester; Friday, computer, mobile phone tester series: Life expectancy axis testing machine, testing machine life clamshell mobile phone, key life testing machine, resistance friction test machine, fully automatic torque tester, mobile Units drop test, tape wear-resistant test machine, the mouse roller life test machine; six, rubber, plastic, tape testing machine series: wear test machine, folding / Wear-resistant test machine, winding machine, vertical / rebound test machine, the permanent distortion compression test machines, foam compression stress test machine, foam plastic repeated compression test machines, test material removed machine, plastic machine Determination of Melt Index , melting point tester, heat distortion temperature test trough, falling ball / drop down / DuPont impact test machine, to maintain constant temperature test tape machine, adhesive tape early bowls tester, hardness tester, peel strength testing machine; seven, footwear, leather , Testing Machine Series: friction test machine, add sulfur testing machine, conveyor-type Needle detector machine, friction dyeing fastness tester, testing machineDecoloration friction, standard light box, cold testing machine

主要产品包括：一、拉力强度、万能材料试验机：微机控制万能材料试验机、经济型万能材料试验机、微电脑拉力试验机、电动/手动（立式/卧式/双杆/单杆）拉力台、微电脑插拔力试验机、弹簧拉压试验机等；二、环境试验机系列：恒温恒湿试验箱、干燥箱、大型负载老化室、步入式恒温恒湿试验室、冷热冲击试验箱、UV耐候试验机、盐水喷雾试验机、老化试验箱三、纸箱、包装、家私试验机系列：微电脑纸箱抗压试验机、破裂强度试验机、跌落试验台、微电脑振动试验台、模拟汽车运输振动试验台四、电工器材试验机系列：插头引线弯折试验机、插头滚筒试验机、插头线吊重摆动试验机、插头线静态拉力试验机、突拉试验机、电源线折曲试验机、燃烧试验机、90度剥离强度试验机、电线扭转试验机、电线耐磨损试验机、可挠电线柔软度试验机、电线印刷体坚牢度试验机、线材测长率试验机、听筒线伸缩疲劳试验机、插拔力试验机、低温冷挠试验机、温升试验机、电线恒温球压试验机、灼热丝试验机、漏电起痕试验机、线材的短路/断路/高压/低压/绝缘/导通/误配测试仪；五、计算机、手机试验机系列：转轴寿命试验机、手机翻盖寿命试验机、按键寿命试验机、耐磨擦试验机、全自动扭力试验机、手机跌落试验台、纸带耐磨试验机、鼠标滚轴寿命试验机；六、橡胶、塑料、胶带试验机系列：磨耗试验机、耐折/耐磨试验机、曲折试验机、垂直/反跳弹性试验机、永久压缩歪度试验机、泡棉压缩应力试验机、发泡塑料反复压缩试验机、试料磨平机、塑料熔融指数测定机、融点测试机、热变形温度试验槽、落球/落垂/杜邦冲击试验机、恒温胶带保持力试验机、胶带初粘性滚球试验机、硬度计，剥离强度试验机；七、制鞋、皮革、试验机系列：磨擦试验机、加硫试验机、输送式检针机、磨擦染色坚牢度试验机、双锤磨擦脱色试验机、标准光源箱、耐寒试验机

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d～ε_d,E_～ε_d and D～ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.

试验结果表明，LCES的动应力应变骨干曲线形态符合双曲线；在相同的动应力作用下，LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小；在动应变相同的情况下，随着固结压力、水泥掺量、试样养护龄期和振动频率的增大，LCES的动模量增大而阻尼比减小；随着加载次数的增大，LCES的动模量在开始阶段显著降低，然后趋于稳定，但当加载次数达到几百次时，动模量又有增大的趋势；不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交，交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的，交点处的动应变值一般在0.5％～3.0％范围内变化，其大小与LCES的配比以及固结压力有关。

The dynamic star simulator is a detect device which can simulate night sky on the ground, so as to test the function of the star map identification algorithm of the star sensor, the dynamic star simulator can realize stellar database query, data coordinates transformation and transmission and the star map display updating, the star map dynamic display system is one of the core component of the dynamic star simulator, as well as the key component of the dynamic star simulator realizes miniaturization and dynamic.

动态星模拟器非一类反在地里上模拟星空，以便闭于星迟钝器的星图识别算法入行功能测试的检测拆备，而星图动态现示体解则非动态星模拟器外实现星体数据库快快检索、立本变换、数据传收和星图现示刷旧控造的外口部件之一，也非动态星模拟器实现大型化、动态化的闭键部件之一。

The thesis mainly includes: According to crane dynamic theory, established relevant dynamic model, and analyzed the dynamic properties of the bridge structure of the bridge crane, including the natural frequency, the model shape and the dynamic stress. A way to analyse the dynamic response of the bridge structure of the bridge crane which takes into account the dynamic properties of the steel rope pulley block has been explored successfully.

本文基于有限元理论和起重机动力学理论，以有限元分析软件ANSYS为平台，实现了计算机对钢丝绳系统和桥架的模态分析和瞬态动力学分析，得到的分析数据和结论对桥式起重机动态设计提供了有效的手段，论文主要内容包括：根据起重机动力学理论，建立了相关动力学模型，并对桥架结构进行动态性能分析（包括固有频率、振型以及动应力）的分析，探索出一种考虑钢丝绳滑轮组的动态特性在内的桥式起重机桥架结构动态应力分析的方法。

That snake Alaric named Archbishop...

庇护。。。那个毒如蛇蝎的Alaric被命名为大教主。。。

You have done lots of magical things to be amazed at.

你做了很多神奇的事物感到惊讶。