查询词典 die off

Company under the product design, engraved die, die-casting, polishing, electroplating, laser engraving, drop models, sanding, painting paint, tin solder, copper welding, silver welding, spot welding shop and product quality testing center.

公司下设产品设计、刻模、压铸、抛光、电镀、激光雕刻、滴塑、磨砂、画漆、锡焊、铜焊、银焊、点焊车间及产品质量检测中心。

The PCVD plasma impregnation process of hot forging die includes surface deoiling, polishing, supersonic cleaning in acetone and alcohol dewatering of the die after quenching at 1070 deg.c and tempering at 530 deg.c; plasma nitriding in a industrial PCVD vacuum furnace; and PCVD plating.

本发明公开了一种精密叶片热锻模具的PCVD等离子体渗镀复合强化方法，将经1070℃淬火，530℃回火后的叶片模具(HRC＝43-50)经表面除油、抛光后浸入丙酮中超声波清洗，酒精脱水；然后放入工业型PCVD真空炉内进行等离子体渗氮和PCVD镀膜处理。

The die contacting press is the special equipment of automobile die .

模具研配液压机是研配汽车模具的专用设备。

ABSTRACT In order to improve the degree of intelligence in press die design CAD system, this dissertation offers the systematic and deep-going research on the architecture and intelligent design methods for press die CAD.

本论文以提高冲模CAD系统的智能化为目的，对冲模CAD系统的体系结构和智能设计方法进行了系统、深入的研究。

These powders are then transferred to the press die without any alteration of the decorative pattern inside the die cavity.

这些粉末然后填入压机模具，而无需改变模腔内的装饰图案。

Chapter 6, based on the above research, an intelligent press die CAD systemPDICADS is developed. This system adopts the multi-agent architecture as her structure, and uses prototype and case based design methods to die structure design.

第六章在上述研究的基础上，我们开发了一个冲模智能CAD系统原型，该系统采用基于多Agent协作的体系结构，在结构设计采用基于原型和事例的方法。

5 Locate die area in frame by moving the track ball allowing the frame to go inside die area. Press ENTER.

在框架内允许移动的地方移到跟踪球从而来定位模的位置，按& ENTER &确定

This paper also introduces a new mold base design method, which applies technique of Case-based Reasoning, and presents the structure and manager of Case Base of mold die of press die.

本论文运用基于事例推理技术，对冲裁模设计中的模具结构设计进行了研究，提出了模具结构的CBR设计方法，并以此为基础提出了冲裁模结构事例库的结构和管理方案。

Figure 32 A 3D die set assembly has the whole picture of the die set in 3D.

图 32 在3D中3D模具装配具有模具的全部图形。

And the designing method, naming and application of the standard die set s of the die_casting die were introduced.

分析了企业内部制定压铸模模架标准的必要性，介绍了压铸模标准模架的设计方法、命名及应

Cable dampener cannot be rolled up but must be hung over the cable.

缆帆不能被卷起，必须保证处于展开状态

"This skylark is a present from my master," he says.

"这只云雀是我主人献上的礼物。"他说。