查询词典 deflection ancle

They include the glide track following system、the quartic curve leveling control system and the lateral deflection correcting system.

三、无人机自动着陆部分：分别设计了下滑轨迹跟踪控制系统、四次曲线拉平控制系统及侧向偏离修正控制系统。

In cases of misalignment or shaft deflection, the rollers are therefore capable of aligning in the outer-ring raceway.

在偏差或轴弯曲的情况下，因此，能够在外圈滚道心轧辊。

In order to solve torsional deflection strength of transformer's spiral winding, the axial current effect on radial magnetic field is analyzed.

针对变压器螺旋绕组扭转变形强度问题，就轴向电流分量对辐向磁场的影响进行了分析，从而为进一步进行大型变压器瞬态涡流场的数值计算提供了依据。

The engineer's call the difference between the two radii deflection.

"工程师的要求两者之间的差额半径"变形。

Based on the resemblance of deflection equation with free vibration equation, the reciprocal theory can be applied to the analysis of free vibration of unidirectional plate,and through which we can easily get the inherent frequency of unidirectional plate with different boundry supporting after assuming the form of free vibration.

利用单向板挠曲面微分方程和振型方程在数学上及力学上的相似性，提出了分析单向板自由振动的功的互等定理法。

The solutions of thin bending rectangular plate with one subtense edges simply supported and the other subtense edges free, large deflection under uniform pressure are obtained by the Reciprocal Theorem Method in this paper. From the results it can ha found that the method is valid in non-linear questions and develops a new access.

主要应用大挠度弯曲薄板的第二类功的互等定理，求解在均布载荷作用下一对边简支一对边自由矩形板的挠曲面方程，计算结果表明，大挠度弯曲薄板功的互等定理在解决非线性问题方面简单有效，为求解相关大挠度问题开辟了一个新的途径。

The research results show that, the relative error of the area and deflection angle of AVEN is less than 1% after compensation.

研究表明，补偿后的矢量偏转角度和面积的相对误差不大于1％。

The maximum relative errors of calculation compare with the results of literature[3] are less than 10%, commonly the errors are still less than 5%. The accuracy of deflection is higher.

计算结果与文献[3]的结果比较，一般误差不超过10％，大多数在5％左右，挠度的精度更高。

The septum (34) is further preferably configured to minimize or eliminate the negative pressure deflection normally associated with the withdrawal of the large diameter luer cannula (32) from an enclosed fluid filled lumen or chamber, by substantially isolating the lumen or chamber from the septum material displacement resultant from luer (30)insertion.

上述隔垫(34)的结构最好设计成能通过把空腔或腔室与因路厄氏连接器(30)插入后所造成的隔垫材料的移动隔离开来，以便减小或消除通常与大直径的路厄氏套管(32)的抽出联系在一起的，因负压而引起的变形。

So the exact prediction and analysis of the deflection status of mill roller, especially for work roll is very important.

对轧机辊系变形尤其是工作辊变形做出准确的预报和分析，是保证板带材成品截面形状及平直度的先决条件。

Continuously improve the production mechanism, to provide customers with better quality products and services.

不断的完善生产机制，给客户提供更优质的产品及服务。

B:Yes, he was the very prize-winner in the court tennis ten years ago?

是的，他是十年前的世界网球冠军。