查询词典 counterclockwise direction

For instance when we enter is enthralled mountain time, the star axle suddenly is called us counterclockwise to hide behind the trees, then we saw right side us to pass through several palace maids slowly, the hair long tow ground.

比如当我们进入神山的时候，星轨突然叫我们左转躲在树木背后，然后我们就看见了我们右边缓缓走过几个宫女，头发长长地拖到地上。

To adjust, loosen locknut and turn adjusting screw clockwise to increase pressure; counterclockwise to decrease.

如果要进行调节，则松开锁紧螺母，并顺时针方向旋转调节螺丝以增加压力；反时针方向降低压力。

To adjust, loosen locknut and turn adjusting screw clockwise to raise the setting; counterclockwise to lower.

如果要调节，则松开锁紧螺母，顺时针旋转调节螺丝提高设置值；逆时针旋转降低设置值。

Once the position of the device was found to be satisfactory and without or with only a trace to small residual shunt was confirmed, the device was released by turning the cable counterclockwise using the pin vise.

选择大于所测PDA最窄直径2～4 mm的Amplatzer封堵器，于透视下经6 F输送鞘管将其封堵于PDA处。10分钟后重复主动脉造影，若封堵器形状、位置满意，无或仅有微～少量残余分流时，可释放封堵器。

Place wrench (08-A10 5) on travel stop nut, rot ate wrench counterclockwise unt il travel stop nutdisengages upper rod.

把限位螺母扳手(08-A105)套在限位螺母上，逆时针旋转扳手，直到限位螺母脱离上阀杆。

C. Using a 2mm Allen wrench, turn the black adjustment set screw clockwise to make the two-speed shift later; turn it counterclockwise

c。 以2mm的L形内六角扳手转动黑色调整螺丝：顺时钟方向转动让2段变速的换档时间晚些；逆时钟方向转动则会提早2段变速的换

To correct direction, first only the air hammer among located in the position corresponding to the correcting direction is actuated and only the ground in the correcting direction is drilled by a predetermined amount.

在方向修正时先仅使其位置与修正方向相对应的气锤工作，仅对该修正方向的地基按规定量进行挖掘。

Based on the analysis of three-dimensional power conductor for DC arc furnace, the electric arc deflection model was set up and the control system of the arc direction was configured. According to the bus bar distribution at the bottom electrodes cooled by water, the arc direction control principle and its configuration were described, The simulation results show that the control system can restrain the electric arc deflection and control the arc direction.

在分析直流电弧炉三维导体布置的基础上，建立了直流电弧的偏工以此作为电弧位置控制的依据，针对水冷钢棒式底电极型的直流电弧炉，阐述了其电弧位置控制的原理和系统组成，并进行了仿真研究，结果表明控制系统可以有效地纠正电弧的偏向总是并可控设定点自由控制电弧以位置。

But time will not allow me come back to the past time. It let me miss my direction on the coordinate axis of life. The original love ask me go ahead in the direction of straight .In that case.I will not meet the 0degree ice .And straight forward this road .I can see the raising sun.And will find out the beautiful view which others will never meet .If I turn my direction into the opposite one .I will just see the mirage, I trusted her. From childish time to grow up. I accepted many regards from different region and different persons.I shows a big smile all the time . I learnt thanks. Thanks for god let me live in such beautiful world. Thanks for the person who care of me; I leant sympathy .

但是时间不允许我再回到原点，它让我在人生的坐标上失去的方向，原本的爱一直指导我向正坐标走，它告诉我那样我不会遇到零度坚冰，一直走下去会看到初升的太阳，会看到很多别人的看不到的美景，它告诉我如果真得往恨的方向走，我看到的只是海市蜃楼，所以我听它的，从小到大，我接收到了来自同或者不同的地域的人的爱护，我一直咧开一张嘴笑着，我开始学会了感谢，感谢上仓让我生在这样一个世界，感谢我身边每一个人对我的关怀；我开始学会同情，同情一些孤儿老人和备受战争残害的人…。。

According to that characteristic and based on the differential equation of the deformed surface of the orthotropic plate, with one principal direction size fixed, changing another principal direction size linearly, maintaining elasticity coefficient the same as in the first principal direction and Poisson ratio equal to the geometric mean of two principal Poisson ratios, the original orthogonal plate is equivalent to an isotropic plate. Results obtained show that the deflections of the equivalent isotropic plate are the same as the deflections of the original orthotropic plate at the corresponding points, the forces of the correspondent points have simple relations.

根据这一特性、从正交各向异性板挠曲面的偏微分方程出发，保持一个主方向尺寸不变，另一主方向的尺寸做线性缩放，保持弹性模量与第一主方向相同，泊松比取2个主方向泊松比的几何平均值，将这类正交各向异性板等效为一块各向同性板；通过分析得到：各向同性板任意点的挠度就是原正交各向异性板对应点的挠度，各对应点内力之间存在简单的比例关系，该文的方法将为工程技术人员提供方便，同时可以更加直观的认识正交各向异性板的受力。

Continuously improve the production mechanism, to provide customers with better quality products and services.

不断的完善生产机制，给客户提供更优质的产品及服务。

B:Yes, he was the very prize-winner in the court tennis ten years ago?

是的，他是十年前的世界网球冠军。