查询词典 cosine function

On that basis, the author points out that material of the oil generation has the multi-component characteristics and that the oils have the multi-source characteristics, and, further, it is indicated that oil formation is a process of multi-source and multi-component compounding and that the process is a part of the continuous hydrocarbon generation model of the damped cosine curve during the burial of sedimentary organic matter in geological time.

另外，对低成熟石油的相关成烃母质进行了综述，在此基础上给出了低成熟成烃母质的定义，指出了低成熟石油成烃母质的多元性和油源的多源性特点，同时还指出低成熟石油是沉积有机质在地质埋藏过程中波动成烃连续模式之部分，其具有多元多源复合成烃行为和分阶段连续演化的特征。

At present the camber process system is more advanced in china. We imported servo-drive equipment with digital control system , greatly improved our process precision, can produce multi-curve camber such as cosine curve. The process ability is up to 680mm in diameter and 10m in length.

该系统是目前国内较为先进的胶辊中高加工设备，采用进口数控系统和高精度的伺服驱动设备，使加工精度大大提高，可加工如余弦曲线等多种曲线中高，加工能力为直径680mm，长度10000mm。

With the same monitoring thickness, the actual thickness of thin film deposited on the substrate decreases gradually as the oblique angle increases, but this thickness is still greater than theoretical thickness revealed by the cosine curve.

在相同的监控厚度时，随倾斜角度增大，沉积到基片上的薄膜厚度逐渐变小，但仍然大于余弦曲线显示的理论厚度。

Results show that parabola is the most suitable one for the displacement-based method, following with cosine curve being the second and then circle the third,while hyperbola is unfit for the method.

认为抛物线最适合在位移法中使用，正弦曲线次之，圆曲线要有所限制，而双曲线则不宜采用。

It is found that,there are two types of interfacial cracking patterns of the ceramic coat: in the cooling process, mode Ⅰ is vulnerable to crack at the peak position of the cosine curve, and mode Ⅱ at the middle position; in the heating process, interface edges are introduced into the ceramic coat/substrate system as a result of the vertical cracks emergence, and the ceramic coat will transversely crack at these positions because of the stress concentration effect.

计算时对陶瓷层材料分别按理想线弹性本构和黏塑性本构模型开展了模拟。分析发现，陶瓷层的界面开裂存在两种模式：在降温过程中，陶瓷层容易出现界面波峰处的Ⅰ型开裂与腰部位置处的Ⅱ型开裂；在升温过程中，陶瓷层容易发生垂直开裂使结构中出现陶瓷层/基体的界面端，界面端部严重的应力集中效应使陶瓷层容易在该处横向开裂形成界面处的边裂纹。

To satisfy the requirements of fast producing,low cost manufacture and large thickness preforming in the field of non-resin winding cylinder composite,the equation of retracing cosine curve was deduced based on the section principle.

最后基于对余弦折回曲线的分析，利用数值模拟证实余弦折回曲线在干纱缠绕圆柱壳体预成型中有利于高速加工；在缠绕厚度相对不大且需要高速缠绕加工情况下，可采用余弦曲线作为端部区段的折回曲线。

Methods Exerting backwards force on rats mandible and measuring concentration of rats' blood cAMP in three groups with radio-immunity. Drawing the time-concentration curve and making cosine analysis.

给大鼠下颌戴向后上牵引的矫形器，用放射免疫法测定不同加力组大鼠血中环磷腺苷含量，绘制时间-浓度曲线，并进行时间生物学的余弦统计分析。

It is determined that the sun vector measurement error is about 5.74° which is caused by many factors, such as the non-ideal cosine curve between incident angle and photocurrent, the photocurrent noise, the nonlinearity of the analog circuit and the A/D converter, and the temperature inaccuracy etc.

通过分析获得太阳入射角——光电流非理想的余弦特性、光电流的噪声起伏、处理电路非线性、A/D采样非线性、温度测量不确定性等因素导致的太阳矢量实际测量误差为5.74°。

The maximal depth model for single-pass milling process, the depth and surface roughness for plane surface are established. The milled profile of a single-pass milling of the jet can be modeled as a cosine curve of the form. Therefore, the maximal depth model for single-pass milling is established which indicates the quantitative relationship between the AWJ single-pass milling depth and the milling parameters.

假设磨料水射流单次铣削时的工件横截面形状为余弦曲线，建立了磨料水射流单次铣削的最大深度模型，分析了水射流压力、磨料流量、靶距、喷嘴横移速度、横向进给量和喷嘴直径及材料性能参数对单次铣削最大深度的影响规律。

Side of the cosine formula ...

边的余弦公式。。。

I can not negligent, he should do what?

我不能不在意了，他要做什么呢？

It is very dangerous to swim in the river alone.

一个人到河里游泳是很危险的。