查询词典 contiguous angle

A very large 10 clearance angle reduces the strength of the tool tip, and hence normally an angle of the order of 5-6°is used.

过大的后角就减小了刀尖的强度，因此，后角通常为 5～6°。

Clearance angle This is the angle between the machined surface and the underside of the tool called the flank face.

后角 这是已加工表面和刀具下面叫做后刀面之间的夹角。

So one more drill point geometric parameter is needed, such as heel clearance angle, chisel edge clearance angle.

为了获得唯一的后刀面廓形，必须增加一个辅助参数。可供选择的补充参数有尾隙角、横刃后角、周边后角、切深后角等。

So one more drill point geometric parameter is needed, such as heel clearance angle, chisel edge clearance angle.

可供选择的补充参数有尾隙角、横刃后角、周边后角、切深后角等。

The important parameters of designed flutes, such as rake angle, clearance angle, are analyzed, and the calculating method of tangential vector, normal vector, and so on, is discussed.

基于刀刃曲线模型和刀槽螺旋面的生成原理，提出了可满足各种设计要求的刀槽螺旋面的几何建模方法，推导了铣刀和旋转锉的多种类型的刀槽螺旋面方程。

Equipment with real-time monitoring, arc, interpolation, helical milling, clearance angle, single angle integrated time for 7-15 seconds.

设备配有实时监控，圆弧、插补、斜铣、单角综合清角时间为7-15秒。

The results show that cutting tools and cutting parameters had an important influence on the quality of the fiber in the planing process of metal fiber. The larger rake angle and appropriate clearance angle of tools favored to fabricate metal fiber. Back engagement influenced the forming process of metal fibers most greatly, feed rate and cutting speed varied little.

研究结果表明：在金属纤维刨削成形过程中，刀具参数和切削用量对纤维的质量有重要影响，较大的刀具前角和合适的刀具后角有利于纤维的成形，而背吃刀量对金属纤维的成形影响最大，切削速度和进给量的影响则不明显。

This paper also makes a experimental study of the regularities of the outstripping machining in aspects of machine tool, cutting tool, cutting conditions and so on, and points out that the outstripping phenomenon occurs on the following conditions: the machine tool with high precision, the PCD cutting tool with small clearance and lay angle, the small installation angle, the small feed rate and the cutting lubricant with good properties, and that the cutting speed and the depth of cut have no effects on the outstripping machining.

本文还从机床、刀具和切削条件等方面对超越性加工的规律进行了实验研究，指出超越性加工现象是在如下条件下产生的：较高精度的机床、后角和刃磨纹理角较小的PCD刀具、较小的安装角和较小的进给量以及冷却润滑性能良好的切削液，而切削速度和切削深度对超越性加工几乎没有影响。

Therefore, Fine copper fibers with stability quality were obtained under setting back engagement for 0.04-0.06mm, cutting speed for 30-60m/min and feed for 0.72-1.44mm/str, and using the tool with rake angle and clearance angle were 30° and 8°, respectively.

在背吃刀量为0.04-0.06mm，切削速度为30-60m/min，进给量为0.72-1.44mm/str的条件下选择前角为30°，后角为8°的多齿刀具，可以获得质量稳定的微细铜纤维。

Decrease of the clearance made the critical angle become bigger and the effect of disc also increase. Larger impeller disc and larger impeller made the critical angle smaller.

当涡轮与搅拌槽底的间隙越小时临界角越大，而涡轮碟盘对於流场的影响也越明显，当涡轮尺寸与涡轮碟盘尺寸越大时，临界角越小。

We were cousins—his grandfather was King of Scots,and his great-grandfather was Henry VII of England.

我们是堂姐弟——他的祖父曾是苏格兰国王，他的曾祖父是英格兰的亨利二世。

I do want to help you, but I am in a quandary now!

我是想帮你，但是我现在左右为难啊！