查询词典 constant current

The study indicated that current and displacement stiffness are constant in the range of allowable engineering error. There is a linear range to the magnetic force. The simplified linear model meets the requirement of controller design. The more precise control precision is, the smaller linear range is.

研究表明，在工程误差允许范围内，位移刚度和电流刚度可视为定值，即此时电磁力方程在应用上存在较大的线性区间，因此简化的线性化模型完全可满足控制器设计的需要，且线性区间随着控制精度提高而减小。

When the system is at work, IF output power is achieved through adjusting inverter trigger angular frequency, which can always make the power out put be in the biggest state . Through the effect of the voltage and current closed-loop ,IF power achieve constant power output.

由于系统在工作时，中频电源的输出功率是通过调节逆变触发角频率来实现的，这样就可以始终使输出的功率处于给定的最大状态，并且通过电压和电流闭环作用，使中频电源达到恒功率输出。

This method is used to solve the eddy current problems of railgun when the velocity of armature is constant.

并且提出了迎风—线性棱边单元法，并用此方法计算了电枢定速运动的电磁轨道炮的涡流问题。

A back electromotive force observer is constructed to acquire the information of speed as well as acceleration. By selecting the time constant or observer gain properly, the current command reduction characteristics can be adjusted freely in some range.

其中的反电动势观测器能方便地获得速度和加速度信息，通过适当调整观测器的时间常数和增益，就能使驱动电流指令值在一定范围内自由调解以达到控制目的。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Using this method, wide dimming range can be achieved with narrow frequency range and constant DC link voltage. And the lamp current keeps perfect sine wave all the time, which means low lamp current crest factor is obtained. Its validity is verified by simulation and experiment.

本章最后提出了一种基于T型滤波器的新型的调光方法，采用此方法可以在保持逆变器直流母线电压和开关占空比不变的情况下，只需很窄的频率范围就能达到非常宽的调光范围，而且在整个调光范围内灯电流都基本上是完美的正弦波，这就意味着可以始终保持很低的灯电流波峰因数，仿真和实验结果充分验证了它的优点。

When left when the test-drive after repair in shop main engine is adding this ship to 540r/min, supercharger occurrence asthma brace up phenomenon, rotate speed lifts slightly again, noise shakes very big, smoke evacuation temperature is normal, hair of on the high side of temperature of air inlet duct is very hot, as good as of smoke evacuation smoke constant, supercharger rotor rotate speed and the rotate speed of right leader supercharger that work normally comparative. 2 breakdown analyse this model diesel engine supercharger breathes heavily brace up the reason has the following sides. Bearing of 1 supercharger rotor damages, bring about on the low side of supercharger rotor rotate speed or wave motion, make inadequacy of compressor part air feed and diesel engine and its demand do not match, bring about air current not to stabilize generation to breathe heavily brace up. 2 diesel engine offers oil, match gas to time forbid, match gas, draw well time and disorder, bring about supercharger to breathe heavily brace up. 3 supercharger nozzle jams, cause smoke evacuation not free, circumfluence of exhaust stroke waste gas, enter jackknife of new energy of life with the below one stroke that take energy of life, produce air current to hit generation to breathe heavily brace up. Canal of 4 smoke evacuation jams, smoke evacuation not free, bring about waste gas circumfluence, hit generation of new energy of life to breathe heavily brace up. 5 jams into gas mouth, enter gas inadequacy, generation breathes heavily brace up. 3 trouble removal are based on above analysis, adopt the following measure to remove trouble.

该舰在厂修后试车时左主机在加至540r/min时，增压器出现喘振现象，转速再略升高，声响震动很大，排烟温度正常，进气管温度偏高发烫，排烟烟色无异常，增压器转子转速和正常工作的右主机增压器转速相当。2故障分析该型柴油机增压器喘振的原因有以下几个方面。1增压器转子轴承损坏，导致增压器转子转速偏低或波动，使得压气机部分供气不足和柴油机及其需求不匹配，导致气流不稳定产生喘振。2柴油机供油、配气定时不准，配气、发火定时紊乱，导致增压器喘振。3增压器喷嘴堵塞，导致排烟不畅，排气冲程废气回流，和下一进气冲程进新气重叠，发生气流冲撞产生喘振。4排烟管堵塞，排烟不畅，导致废气回流，冲撞新气产生喘振。5进气口堵塞，进气不足，产生喘振。3故障排除基于以上分析，采取以下办法排除故障。

Constant temperature bath was employed to get the curve of forward current and temperature, which will be the basis of forward current feedback and temperature conversions. Self-developed driving circuits were used to control LED to make the relative illumination decays to be less than 5% and the coordinate excursion of Color rendering indix on the CIE chromaticity diagram is lower than 0.1. The development of circuit control of LED projection light with low aberrance of illumination and Color rendering indix, changing with the temperature can be successfully realized.

研究执行首先针对各类LED单体，进行晶粒温度对前馈电流变化之量测，利用恒温槽控制得出完整曲线，并以此作为LED晶粒前馈电流回授与温度换算之依据，利用自行开发脉波驱动线路，进行高瓦特LED单体控制，达成相对照度变化小於 5%，演色性在CIE chromaticity diagram上座标偏移低於0.1，成功实现一随温度变化，照度与演色性变异均低之LED投射灯控制线路开发。

At equilibrium,the rate of the metal dissolution is equal to the rate of the cathodic reaction,and the rate of the reaction is directly proportional to the current density by Faradar's law ;therefore:（6）and the Nernst equation can be rewritten(7)where B is a constant and i0 is the exchange current density,which is defined as the anodiccurrent density at the standard electrode potential.

在平衡，金属溶解的率与负极反应的率是相等的，并且反应的率与电流密度直接地是比例由Faradar的法律；因此：(6)和能斯脱等式可以被重写(7) B是常数的地方，并且i0是交换电流密度，被定义作为正极电流密度在标准电极电位。

Since historical times,England ,where the early inhabitants were Celts, has been conquered three times .

从有历史以来，英国，在此地早期居住的是凯尔特人，已经被征服了三次。

Bluetooth OBEX File Transfer Enables the sending and receiving of files on your phone via Bluetooth.

蓝牙OBEX文件移动允许经过蓝牙传送和接受文件。。。。