查询词典 composites

The results of thermal property of DSC for PP composites show that two melting temperatures implied immiscibility for PP composites. The melting temperature and corresponding fusion heat for PP material was not changed by additives. Therefore, the immiscibility PP composites resulted in their poor mechanical properties.

聚丙烯复合材料出现双峰现象，此处显示各组有不相容之材料，因材料的不相容，将导致机械性质的降低，图中可知添加的材料对聚丙烯之融熔热与熔点皆无显著改变。

The strength of SiCp/Al composites hot-pressed above and extruded below, or hot-pressed below and extruded above the solidus temperature of the matrix is higher than that of composites hot-pressed and extruded above or below the abovementioned temperature, and the strength of SiCp/Al composites hot-pressed above and extruded below the solidus temperature of the matrix is the highest.

以基体合金的固相线温度为基准，高温热压、低温挤压或者低温热压、高温挤压的复合材料的强度优于高温热压挤压或者低温热压挤压的复合材料，并且高温热压、低温挤压的复合材料的力学性能最优。

Many new type of composites come forth continuously recently,such as thermosetting composites and thermoplastic composites.

近年来，许多新型复合材料不断涌现，如热固性复合材料和热塑性复合材料等。

SiC/Al composites were prepared with pressureless infiltration method. Using pin on disk tribometer, the influence of volume fraction and particle size of SiC on dry friction and wear properties of the SiC/Al composites were investigated. The wear mechanism of the composites was studied with the analysis of the worn surface by SEM.

采用无压浸渗法制备不同碳化硅粒度和体积分数的SiC/Al复合材料，利用销－盘摩擦磨损试验机考察了碳化硅的粒度和体积分数等对SiC/Al复合材料干摩擦磨损性能的影响，采用扫描电子显微镜观察磨损表面形貌并分析其磨损机理。

9GPa respectively, and those of random short fiber composites are 145MPa and 13. 0GPa respectively. Therefore, the initial mechanical capability of unidirectional long fiber and short fiber composites of CPP/PLLA is able to satisfy the requirement of mechanical capability of internal bone fixation materials for cortical bone, and random short fiber composites of CPP/PLLA for cancellated bone.

因此，CPP/PLLA单向长纤维及单向短纤维复合材料的初始力学性能满足承重骨骨内固定材料的力学性能要求；CPP/PLLA随机短纤维复合材料的初始力学性能满足松质骨骨内固定材料的性能要求。

Carboxy styrene-butadiene rubber/sodium based clay composites were prepared by emulsion intercalation, the microstructure of the composites was characterized by X-ray diffraction, and the mechanical properties and dynamic mechanical properties of the composites were studied.

用乳液插层法制备了羧基丁苯橡胶／钠基黏土(XSBR/Na-clay)复合材料，用小角X射线衍射仪对其微观结构进行了表征，并对其动态力学性能和力学性能进行了研究。

The mechanical characteristics of the foam filled 3-D spacer fabric composites under flatwise compressive , shear and three point s flexural loads were compared with 3-D spacer fabric composites and foamsandwich composites , and the effect s of pile height and foam density on the mechanical properties were investigated.

将三维间隔连体织物泡沫夹层结构平压、剪切和三点弯曲载荷作用下的力学特性与三维间隔连体织物复合材料、传统泡沫夹层结构复合材料进行了对比分析，在此基础上，考察了芯柱高度、泡沫密度对复合材料平压、剪切、三点弯曲性能的影响。

The results show that the polymer determines the electricity conducting of coal filled polymer composites. The coal filled PP composites is an insulating material, and be independent of coal type, its direct current resistivity is above 10〓Ω·cm. The resistivity drops with the content of coal when using anthracite, but it is also above 10〓Ω·cm, and the surface modification of coal, especially alkylated, resumes the insulance of composites.

X射线衍射测试表明即使在高变质程度下煤中的石墨晶区含量仍较低，煤填充聚合物复合材料电性能主要由基体材料性能决定，通过动电容静电计对煤填充聚丙烯复合材料直流电导性研究表明，煤填充聚丙烯复合材料是绝缘材料，其绝缘电阻在10〓Ω·cm以上，在高含量情况下，仍能保持良好的绝缘性，而与煤种无关。

In order to enhance the compatibility of ABS/PP/CaCO3 composites, the effects of reactive blends of the composites were studied by using Haake rheometer. The effects of various assistant cross-linkingers, such as castor oil, triallyl isocyanurate, turpentine (JS-1) and glycol dimethacrylate, and the used amount of cross-linkinger-dicumyl peroxide on the torques of the melting composites were investigated.

为提高ABS/PP/CaCO3复合材料相容性，采用转矩流变仪观察了ABS/PP/CaCO3三元复合物反应性共混后的扭矩，考察了不同的助交联剂蓖麻油、异氰脲酸三烯丙酯、松香酯(JS-1)、二甲基丙烯酸乙二醇酯以及交联剂过氧化二异丙苯的用量对共混物的影响。

And the PLA/Chitosan/ACP barriers with additional 2 wt% chitosan still maintain 56.58 % antibacterial ability after eightieth day. The different composition of PLA/Chitosan/ACP composites was prepared by water washing solidification from NMP/water/lactic acid consolvent. After storing at room temperature for 48 hours and taking it out to obtain a shapable composites. To investigate the influence of ratio of composition with the shapable property of composites, it was analyzed by Rheometer, TGA, AFM, XRD. The result of the different APC content had different effect both water content and yield stress of composite materials. The yield stress decreased with ACP content while increases. It was derived that ions, released from ACP interact with amide groups of chitosan to form water-absorbing ionic clusters through chelating or electrostatic attraction.

另外，以聚乳酸/几丁聚醣作为基材并添加不同比例的非晶型磷酸钙，经过水洗固化后可得白色片状沉淀物，於室温下静置48小时后，复合材之体积呈现膨胀且具有可塑形之特性，以热重分析仪与流变仪分析样品之含水率与屈伏应力，结果显示不同ACP含量对复合材含水率与屈伏应力具有消长变化，而PLA/Chitosan/ACP之可塑程度与其所吸收之水份多寡有关，推测可能机制为ACP磷酸钙盐解离后之金属离子与几丁聚醣之胺基透过螯合作用或静电吸引之交互作用，形成具吸水性之离子团簇分散於疏水性之聚乳酸基材中。

Must have Coordination and negotiation skill, flexible ideas, and be punctilious person.

必须具备较好的协调与谈判能力，头脑灵活，工作认真仔细

Result: 18 patients are all with simple eye.The pigment mole lies in nasal and temple sides of the ball conjunctiva,in which 2 lie in lacrimal caruncle and semilunar plica.

结果：18例患者均为单眼，色素痣大多数位于内外侧睑裂部球结膜面，2例位于泪阜及半月皱襞，经激光治疗后，10例色素痣消失，有5例行再次激光后消失，2例行第三次激光后消失，1例第四次激光后消失。