查询词典 complementary angle

Angle of wipe: In rotogravure printing press, the angle between the doctor blade and the engraved cylinder.

刮墨角：在轮转式照相凹版印刷机上，括墨刀与凹版圆筒所成的角度。

Angle of wipe: in rotogravure pr in t in g press, the angle between the doctor blade and the engraved cyl in der.

刮墨角：在轮转式照相凹版印刷机上，括墨刀与凹版圆筒所成的角度。

In mathematical terms, the Facing Ratio is the Dot Product of the angle rather than the angle itself.

在数学术语上，Facing Ratio是角度的数量积相当于角度本身。

In strictly, it is hard to make the light normal incident into the sphere, double refraction will take place in crystal sphere when a TEM〓 mode Gaussian beam oblique incident into the sphere, and the two orthogonal polarized beams are both elliptical Gaussian beam. The ellipticity and eccentricity of the elliptical Gaussian beam will change with the incident angle, and for a fixed incident angle, they will change with the shifting of incident beam waist position.

由于严格意义上的正入射较难实现，基模圆高斯光束斜入射晶体球后将在球内产生双折射，且球内偏振态正交的两束折射光都将是椭圆高斯光束，它们的椭圆度e和偏心度Δ随入射角的改变而改变，在入射角一定的情况下，入射光束束腰的移动也将改变这两束折射光的椭圆度e和偏心度Δ。

The expression of cogging torque is deduced on dual-stator permanent magnet synchronous machine, and the influence rules of the resulting cogging torque are analyzed with the change of relative angle between dual stators. The relation between cogging torque amplitude and the relative angle between dual stators is investigated. Finally, simulation verification is conducted based on finite element method.

针对双定子永磁同步电机，推导了内外定子及其合成齿槽转矩的解析表达式，分析了内外定子相对位置变化对合成齿槽转矩的影响规律，着重研究了合成齿槽转矩幅值与内外定子相对位置的关系，最后用有限元方法进行了仿真验证。

In addition, spot color screen angle in software will normally be preset to 45 ° c (45-degree, is considered the most comfortable utilizinghuman-aware, so that the angle of the dot is arranged in horizontal and vertical lines to equal rotation, you can reduce the human ability to mesh point detection), if a Duotone image or data file into the existing business card printing and membership card making four color black%(General in the four-colour screen business card printing and membership card-making Black mesh point-and-drop, in a 45-degree is 0 degrees for yellow, magenta to 15 degrees, 75 degrees), and spot color, or with more than two spot colors, the color screen is to a 45-degree output, so use the spot color, while if it is possible with other screening to overprint colors, you must open the output color separation software color settings or the print dialog box, on the halftone angles to make modifications.

另外，专色的增网角量在软件洋凡是城市预撤为45量（45量均被觉得是人眼感知最安适的角量，让网不背摆列在与程量和垂直线不败不等角量的标的目的上可以裁减人眼差网不背的发现本领），若是一个单色调影像或是数据文件洋既有制卡和会员卡制息四色暗不败外（凡是在四色增网制卡和会员卡制息洋，不兵暗网不背不收在45量，黄为0量、品赤为15 量、青为75量），又有专色，或者是有两个以上专色，则在分色增网时城市以45量输入，所以在差专色搁置浅网时，如果有不定与其他增网颜色有叠印，则务必在分色输入时开放软件颜色撤定或打印撤定的差话框，差专色增网角量举动编削。

The article bases on the traditional graphical method,and applies design principle in the references[1],derives the optimizing design methods which under the condition of meeting the fixed slider stroke and the coefficient of variety of stroke velocity,makes the minimum transmission angle of the eccentric crank slider mechanism to maximum(that is the best transmission angle).

曲柄滑块机构在工程上应用十分广泛，传动角的大小是衡量机构传力性能好坏的一个重要指标。通常求解最佳传动角的方法是建立数学模型，在计算机上进行数值求解，本文在传统图解法的基础上，运用文献[1]中的设计原理，推导出在满足给定的滑块行程S和行程速度变化系数K的条件下，使传动

Because of the small-angle approximationof the parabolic system,we say the result of the elliptic system is relatively reliablein the interval of large ray angle.

由于抛物方程的小角度近似，我们认为在大掠射角区间内，椭圆方程的考察结果是比较可靠的。

The experimental results indicated that the light-induced MR molecular reorientation effect, the so-called twisted angle, caused by the adsorbed MR, decreased with increasing ellipticity of the elliptically polarized green light. Notably, zero pre-tilt angle of LC alignment was achieved in this experiment.

再利用不同光强度的圆偏振绿光雷射激发MR，观察并探讨MR吸附的结果，实验结果显示在圆偏振光各方向能量均等的情况之下，不会有扭转角跟倾角产生，且在吸附面上有不均匀的成核现象发生。

A new algorithm of target classification was presented based on the ellipticity angle and the orientation angle.

基于新方法获得的目标最佳极化，提出了一种目标分类算法。

If I didn't care what anyone thought, I would.....

如果我不介意别人怎么看，我会。。。。

In recent decades, Chile has mandated earthquake-proofing for new structures, requiring that materials like rubber and features like counterweights be built into the architectural designs to allow buildings to bend and sway during temblors rather than break.

在最近数十年里，智利已经为兴建防震的新土建结构而对建筑材料提出要求，需要的材料类似于橡胶，而特性就象运用在建筑设计中的平衡物体，一旦应用以后，当地震发生时建筑就能弯曲摇摆。