查询词典 catalysts

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Three kinds of ionic liquid were used to support the acetylacetone at the C3 position directly according to the method indicated above. These synthesized ionic liquid supported acetylacetone catalysts include imidazolium salts ionic liquid supported acetylacetone catalysts, pyridinium salts ionic liquid supported acetylacetone catalysts and ammonium salts ionic liquid supported acetylacetone catalysts. All these catalysts were characterized by ~1H-NMR,~(13)C-NMR, IR and elementary analysis.

采用设计过程中预期能够提高乙酰丙酮金属催化剂催化氧化活性的修饰方式，合成了三类离子液体支载的乙酰丙酮金属催化剂：咪唑型离子液体支载乙酰丙酮金属催化剂、吡啶型离子液体支载乙酰丙酮金属催化剂、胺型离子液体支载乙酰丙酮金属催化剂，并采用核磁共振氢谱、碳谱，红外光谱及元素分析来对这些新型的催化剂进行了表征。

Among them, the catalysts with the support of SAPO zeolite performed well properties, Pt catalysts exhibited better performance than Pd catalysts, the activity and selectivity of noble catalysts were much better than that of non-noble metal catalysts. The carbides and oxides of W and Mo also performed well for n-heptane isomerization.

正庚烷异构化催化剂中，研究较多的是以SAPO、HZSM-5和Y、β型分子筛为载体的贵金属催化剂，其中SAPO分子筛载体的性能较优，Pt比Pd具有更好的催化性能，非贵金属／分子筛催化剂的活性比贵金属／分子筛催化剂相差较大。

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene PolymerizationFacile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that:1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明：1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体；2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene Polymerization Facile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that: 1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明： 1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体； 2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

The progress of catalysts, which include composite-oxides catalysts and heteropoly compounds catalysts, for selective oxidation of isobutylene to methacrolein were summarized, the mechanism of this reaction on Mo-Bi catalysts was discussed.

本文综述了异丁烯选择氧化生成甲基丙烯醛催化剂，其中包括复合氧化物催化剂和杂多化合物催化剂等的研究现状，讨论了在Mo-Bi催化剂上异丁烯选择氧化生成甲基丙烯醛的反应机理。

The results of the dissertation were concluded as follows:(1) It is essential to deposit a basic additive on the Mo-based catalysts for the synthesis of CH_3SH. The potassium-doped Mo-based catalysts exhibit the highest activity than that of the catalysts doped with the otherⅠA andⅡA group basic promoters. H_2-TPR and LRS characterizations suggest that the addition of a base leads to the transformation of octahedrally coordinated Mo to tetrahedrally coordinated Mo, thus leads to the split of low temperature reduction peaks. The interaction between the basic components and Mo lead to the formation of B-Mo interface phase, which are closely correlated with the formation of CH_3SH.(2) It has been found that Fe, Co, Ni and Te have evident promoting effects for the K-Mo/SiO_2 catalysts.

主要结果归纳如下：(1)在Mo基催化剂中，必须添加碱才具有可观的合成甲硫醇活性，在IA和IIA族元素中，K是最佳的碱促进剂，当K/Mo摩尔比为2，前驱体为K_2CO_3，采用共浸法制备的K-Mo催化剂活性最高。H_2-TPR和LRS表征显示，碱的加入导致表面八面体钼氧物种向四面体转化，催化剂的低温还原峰发生分裂，碱助剂与钼之间存在强相互作用形成了B-Mo"界面相"，该物种与合成甲硫醇密切相关。

The series of catalysts for dehydrogention of n-butane to 1-butene, including oxidative dehydrogenation with Vanadium-based 、molybdates、metal pyrphosphates catalysts and catalytic dehydrogenation with Pt-based catalysts and ZSM-5 zeolite, are reviewed, the membrane reactor with catalysts is also discussed .

综述了对正丁烷脱氢制备正丁烯的催化剂体系，包括有氧脱氢中钒基催化剂、钼酸盐系列和焦磷酸盐系列催化剂；催化脱氢中贵金属Pt系催化剂、以ZSM-5分子筛为载体的催化剂以及膜反应器。

Thus, the synthesis of anisole by O-methylation of phenol with DMC had been extensively investigated using phase transfer catalysts, organic alkaline catalysts or zeolites catalysts.

相转移催化剂，有机碱类催化剂以及分子筛催化剂是DMC甲基化苯酚合成苯甲醚这一反应的高效催化剂，研究的比较广泛和深入。

We stopped by the old fashion ice cream parlor Manhattan Beach Creamery for some refreshment. The "No Shoes, No Shirt, No Problem" sign on the wall epitomizes the beach lifestyle.

我们去商店区的一家老式冰淇淋店坐坐，墙上挂著「没鞋，没上衣，没问题」的牌子完全捕捉了海滩生活的随性及风格。

"If therefore", argues Bellarmine we can offer our prayers and our satisfactions in behalf of those detained in purgatory, because we are members of the great body of Christ, why may not the Vicar of Christ apply to the same souls the superabundant satisfaction of Christ and his saints--of which he is the dispenser?

" "因此，如果"，认为贝拉明（德indulgentiis ，十四）"我们可以提供我们的祈祷和我们满意的代表那些被拘留在炼狱，因为我们是成员的伟大基督的奥体，为什麼可能不是牧师基督适用於同样的灵魂满意的过剩是耶稣和他的圣人-他是在配药？