查询词典 butt

I've worked my butt off on vocabularies all day.

我已经在单词上耗费了一整天了。

I've worked my butt off on vocabularies all day.

我每天都在看词汇。

I've worked my butt off on vocabularies all day.

我一整天都在背单词。

I've worked my butt off on vocabularies all day.

我一整天时间都用在单词上。

I've worked my butt off on vocabularies all day.

我已经是把全天所有的精力都花在记单词上面了。

It's just everytime when I'm in the lunch yard and he's with ten of his butt-kissing weasels...

只是每次当我在吃午餐的院子里时，他和他的10个爱看笑话的孤朋狗友。。。

The influence of residual stresses is not same when the structure of the butt welds is different.

对接焊缝在不同坡口型式时残余应力的影响是不同的。

He is wide in the butt and massive in the thighs.

他要有宽大的臀部和粗壮的大腿

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

Ennis picked out a big chestnut called Cigar Butt to ride, Jack a bay mare who turned out to have a low startle point.

艾尼斯选了一头叫做巴特雪茄的栗色马来骑着，而杰克骑了一头有点受了惊吓的母马。

There had been a moment during the breakfast meeting, though, after the backslapping and the small talk and when all of us were seated, with Vice President Cheney eating his eggs Benedict impassively and Karl Rove at the far end of the table discreetly checking his BlackBerry, that I witnessed a different side of the man.

那次早餐会期间，在表示过关心和寒暄以后，我们所有人坐了下来，我注意观察了一下，副总统切尼面无表情地吃着班尼迪克蛋（Eggs benedict，源自美国，以英式松饼、火腿、水煮蛋以及荷兰酱组合而成），卡尔。罗夫在餐桌的远端谨慎地经常查看他的黑莓手机，我目睹了他所不为人知的一面。

Talk Undelete failed; someone else may have undeleted the page first.

Talk 无法删除选定的页面或图像（它可能已经被其他人删除了）。