查询词典 butt chisel

Yun-strip method, the circle-shaped bath temperature higher than the crescent-shaped article transport transport of temperature, the temperature was higher than the crescent-shaped article transport serrated Article transported bath temperature, in the 12mm flat bottom welded seal, using serrated transport of , and with the magnitude and the swinging groove on both sides of the pause, effective control of the bath temperature, so that pore size of the melt is essentially consistent with the roots do not form a welding groove tumor and decrease the chances of burn-through, no penetration has The improvement of the peace panels of the single-sided welding butt welding flat-sided shape is no longer difficult.

运条方法，圆圈形运条熔池温度高于月牙形运条温度，月牙形运条温度又高于锯齿形运条的熔池温度，在12mm平焊封底层，采用锯齿形运条，并且用摆动的幅度和在坡口两侧的停顿，有效的控制了熔池温度，使熔孔大小基本一致，坡口根部未形成焊瘤和烧穿的机率有所下降，未焊透有所改善，使乎板对接平焊的单面焊接双面成形不再是难点。

I like to vent a gas balloon, a butt to sit down and yell:"It is really too dumplings" obedient ", and I do not pack a!"

我像泄了气的皮球，一屁股坐下来，嚷嚷道：&这饺子真是太不&听话&了，我不包了！&

Products mainly include: various types of resistance points welding machine, butt welding machine, seam welding machine, stud welding machine;òautomatic hydraulic machines, mechanicalòmachine, play button machine; automatic transfer straight cut machines, trimming machines; gas shielded welder (CO2 welding machine, welding machine) punch press with automatic feeder, such as pneumatic five categories.

产品主要有：各类电阻点焊机、对焊机、缝焊机、螺柱焊机；液压全自动打圈机、机械式打圈机、打扣机；全自动调直切断机、修边机；气体保护焊机（CO2焊机、氩弧焊机）冲床自动冲压用气动送料机等五大类。

The soldier strikes the side of the sentry's neck with the knife butt or a hammer fist strike (Figure Step 2), which completely stuns the sentry for three to seven seconds.

袭击者用刀柄或者拳头猛击哨兵的脖子侧面（图中step2），哨兵将在3-7秒内完全失去知觉。

Full-length cut - The tail of the jacket is longer in the back than the front of the jacket; cut a bit longer than my other hardshell jackets - a couple of inches below my butt.

全长剪裁——外套的尾部比前部长，剪得比我其他的硬质外套的末端长2英寸

The results show that laser-arc welding can achieve full penetration by single-path butt jointing through appropriate parameters; Y shape groove with 8 mm truncated edge can enhance the penetration ability of laser-arc hybrid welding. Low welding speed is good for penetration, however the limitation still exists for hick plates joint. Gap is significant factor of penetration when work pieces is large thickness. The hardness of thick plates joint shows that there is big difference in mold of vertical thermal cycle using laser-arc hybrid welding.

结果表明：通过激光功率等焊接规范匹配，激光-电弧复合焊接能实现20 mm厚板的全熔透单道对接；钝边为8 mm的Y形坡口有助于提高厚板激光-电弧复合焊缝熔透能力；降低焊接速度有利于提高熔深能力；工件厚度较大时，装配间隙对焊缝熔深能力的影响较为显著；接头硬度表明厚板激光复合焊焊缝纵向热循环模式存在较大差异。

Jesters gonna spank your butt. Spank you on thebutt.

杰斯特来打你屁股，来打你屁股！

"I wish I had a stone for the knife," the old man said after he had checked the lashing on the oar butt.

我真希望有一块石头好磨刀，」老人检查过桨柄上的绳子之后，他说。

"I wish I had a stone for the knife," the old man said after he had checked the lashing on the oar butt.

&但愿有块石头可以磨磨刀，&老人检查了绑在桨把子上的刀子后说。

First of all, the concept of S-N curve and the procedures of p-S-N curve fatigue test, data processing were introduced. And then, these procedures were taken into practice on 4 kinds of aluminum alloy welded joints: corner joint, butt joint, cruciform joints and double-sided lap joint.

文中首先介绍了S-N曲线的概念和p-S-N曲线疲劳试验方法和数据处理方法，并按照这些方法对角接、对接、十字接和双面搭接四种铝合金焊接接头试样进行了疲劳试验，得出了这四种焊接接头的中值S-N曲线和置信度为95%，存活率分别为90%、99%下的p-S-N曲线及其方程。

"The operators will suffer a temporary decrease in the number of consumers and short message services as people may not like having to provide their ID cards for a phone number," Xu Junqi, vice-dean with the Policy-Making Institute of the Telecommunications Research Centre under MII, said yesterday.

信息产业部下属的通信决策研究院副主任徐俊其昨天说：&实行手机实名制后，人们可能不太情愿用身份证注册手机号，所以通信运营商会暂时面临用户减少和短信用户减少的问题。&

I don't believe in make-believe!

我不相信这些虚构的故事。