查询词典 bearing bar
- 与 bearing bar 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
A support member is connected to the one-sided end of the screw member while centrally bearing a support bar protruded opposite to the screw member.
一支撑件连接到螺纹件的一端,且其中心具有向与螺纹件相反方向伸出的支撑杆。
-
End-suction centrifugal pumps, rating with 10 bar with bearing bracket - Nominal duty point, main dimensions, designation system
带支承架的额定值为10bar的端吸式离心泵。公称负荷点、主要尺寸和命名系统
-
Rebar disposition: Rebars must meet requirements on the design drawings in respects of grades, diameters, pieces, spaces, joints, position and length of bearing steel bar, thickness of protective course, etc.
b。 钢筋配置:钢筋必须符合设计图纸要求的级别、直径、根数、间距、接头、负筋位置与长度、保护层厚度等。
-
Four aspects as parties withdrawal of admission, People s Courts investigating and collecting evidences under authorization, applying reappraisal, attestors bearing witness at bar are expounde.
随着民事审判方式改革的深入和我国加入WTO ,完善民事诉讼证据立法是健全民事诉讼制度的迫切需要。
-
End-suction centrifugal pumps, rating 10 bar with bearing bracket - Nominal duty point, main dimensions, designation system; German version EN
带轴承座和 PN10轴向端口的离心泵。额定功率。主要尺寸。标识系统
-
The product mainly applied in:water conservancy and hydroelectric power industry,hydro slide way,hydroturbine entrance bucket bearing,connecting bar,thrust ring,resistance to ware board,spindle collar,steeling rolling industry,mine equipments,forging and pressing,mutallurgyequipments,automobile industry,rubber-plastic industry.
该产品广泛应用于:水利水电行业,水工滑道,水轮机导叶轴承,连杆,止推环,抗磨板,转轮轴套。轧钢行业、矿山机械、锻压机床、冶金机械、汽车行业,橡塑行业等。
-
The only major difference is that boring jigs are normally fitted with a pilot bushing or bearing to support the outer end of the boring bar during the machining operation.
唯一最重要的差别是镗夹具一般用于控制衬套,或者在机器操作时支撑镗杆的外端。
-
The bearing capacity of coupling beam isinfluenced by span-depth ratio, longitudinal bar ratio and stirrup ratio, and so theabove-mentioned factors should be considered in the calculating formulas.
跨高比,纵向配筋率以及配箍率对承载力均有一定的影响,因而建议应在承载力计算中考虑跨高比,纵筋率以及配箍率等因素。
-
The vertical load on the underpinning-node resisted by shear capacity of bolt, new-old concrete interface and profiled bar fringe embedded in column. A formula calculating bearing capacity of the underpinning was advised, and the combined work was calculated by cooperate coefficient γ.
分析认为托换节点的竖向荷载由螺杆的抗剪承载力、新旧混凝土连接界面的抗剪能力和型钢翼缘卡入柱身产生的咬合力共同承担,由此给出了型钢对拉螺栓柱托换节点的抗剪承载力计算公式,式中通过综合作用系数γ考虑了3部分的共同作用和相互影响。
-
Offices have been given in the load-bearing spring steel bar reinforcement spring, fixed spring of fabric to be difficult to corrosion and tasteless, covering the spring on the characteristics of the fabric Ibid.
在承重弹簧处应有钢条加固弹簧,固定弹簧的织物应不易腐蚀且无味,覆盖在弹簧上的织物同上特性。
- 推荐网络例句
-
Chrysanthemum of 10 thousand birthday is lax to edaphic requirement, with the arenaceous qualitative loam with fecund, good drainage had better.
万寿菊对土壤要求不严,以肥沃。排水良好的砂质壤土为好。
-
He unstepped the mast and furled the sail and tied it.
他拔下桅杆,把帆卷起,系住。
-
Therefore, positively advances the interest rate marketability reform is one of current our country finance reform important tasks.
因此,积极推进利率市场化改革是当前我国金融改革的重要任务之一。