查询词典 azimuth angle

It deducts the formulas of azimuth angle and attitude angle and uses fixed-point DSP to realize the arithmetic of the angle.

推导了方位角和姿态角的理论公式，并实现了角度的定点DSP算法。

This paper introduces an analytic method of quick north seeker , whose principle is to use gyro to sense the component value of the angle-rate of the earth rotation, with which the northern azimuth angle between the referenced shaft of carrier and actual north angle can be measured.

本文提出一种基于解析的快速寻北方法，其原理是利用陀螺仪敏感地球的自传角速率分量，并由此计算出载体的参考轴向与真北方向的夹角，即偏北角。

Simulation result shows that the alignment accuracy was 5' for east direction maladjustment angle error, 2' north direction maladjustment angle error, and 6' for azimuth maladjustment angle Error.

仿真结果表明该方案的对准精度(1σ)可以达到东向失准角误差为5角分，北向失准角误差为2角分，方位失准角误差为6角分。

The result indicates, under the condition of big initial error and shell"s high speed rolling, after 60 seconds" flight alignment, the error of azimuth angle and attitude angle can be decreased to no more than 10 angle second, and the position and velocity error has been corrected. This shows the effective of our designed arithmetic.

研究结果表明：在初始误差较大、弹体高速旋转的条件下，经过60秒的空中对准，三个姿态角误差可降至10个角秒以下，同时位置和速度误差得到了修正，从而验证了算法的有效性。

At present, the location of the anti-lopsided wear centralizer used in fields is mainly based on the deviation angle. In fact, lopsided wear may be caused by the change of azimuth angle or by the vertical well section and hold angle section during the working of the bucket rod.

目前油田矿场主要根据井斜角来确定防偏磨扶正器下入位置，实际上方位角变化也能导致偏磨，抽油杆杆柱在运动过程中直井段和稳斜段也会产生偏磨。

The pit shaft parameters of the elevation angle,the azimuth angle,the tool of facial angle and so on are obtained after the computation.

陀螺测斜技术以动力调谐速率，陀螺测量地球自转角速率分量和石英加速计测量地球加速度分量为基础，经计算得出井筒的倾斜角、方位角、工具面角等参数。

The system can automatically seek north when the vehicle is immobile. And the time consumption is no more than 5.5 min. Besides, the system can keep azimuth angle and provide tilt angle and pitch angle of the vehicle.

本系统可以在车载条件下，停车完成自动寻北，寻北时间小于 5.5min；本系统还具有在机动时进行方位保持、实时提供载体倾斜角和俯仰角等功能。

As walk-off angle and acceptance angle of beam limit the conversion efficiency and the tunable wavelength range of difference frequency generation, research include effective nonlinear coefficient, walk-off angle and acceptance angle as functions of wavelength, the relationship between conversion efficiency and acceptance angle, and the impact of crystals length on the process of frequency conversion.

由于光束的走离角、允许角限制了转换效率和差频调谐波长范围，研究内容还涉及了有效非线性系数、走离角和允许角与波长的关系，转换效率与允许角的关系，以及晶体长度在频率变换过程中产生的影响。

Based on force diagram an analytical expression between some factors and splaying angle of the bar is brought forward, pointing out that splaying angle of the bar should be 2 3 degrees, and slitting angle should be 30 degrees approximately, outboard slant angle on the slitting groove should be 45 50 degrees and bite angle should be 7 8 degrees.

为稳定小规格带肋钢筋的三线切分轧制，对涉及棒材张开角的切分孔孔型诸角度进行了分析，通过对轧件受力状态的讨论，提出了诸因素与棒材张开角之间的解析式，指出满足三线切分稳定轧制时的棒材张开角应为 2°～ 3°，相应的孔型切分角为 30°左右，孔型外侧壁倾角应在 4 5°～ 5 0°之间，咬入角可控制在 7°～ 8°之间等。

Under the vertical load, the strength of rock mass is higher when there is only one group of joint and the dip angle is less than 20 or higher than 80; When dip angle is between 20 to 80, the strength of rock mass is much lower, it is smallest when dip angle is about 50, and it is lower when this kind of dip angle is in combination with other angle.

7在铅直向荷载作用下，岩体中只存在一组倾角小于20°或者大于80°时，岩体的强度相对较高；当岩体中存在一组节理的倾角在20°～80°间时，岩体的强度值很小，而且在与其他倾角的节理组合时，岩体的的强度值变化不太大，特别是当节理倾角为50°左右的时候，岩体的强度相对最低。

It was just a normal day of school

那只是上学的普通一天

Which is a very good reference in this issue.

这是一个在这个问题上很好的参考。