查询词典 automatic control system

The main content of this thesis is as follows: 1The structures of EPS are analyzed. The main components of EPS are introduced in detail. Then the distributed torque in EPS is analyzed and the control system model is set up. 2Three control modes are discussed and the control strategy of EPS is studied in detail. Three principal modules in the control strategy are discussed—the predicted module which predicts motor rotational speed and steering rotational speed, the power-assistant module and the return control module. 3The assistant torque curves of the motor are designed by using the B-spline, so that any kind of custom-built assistant torque curves can be designed according to different kinds of automobiles. 4The hardware frame of EPS is studied. The developed controller based on 8-bit MCU MC68HC908MR8 is introduced and many related circuit units are designed, including the control circuit, the driver control circuit and so on. The software structure is discussed, then the steering control program flowchart is given.

本文的主要工作有： 1分析了EPS 的总体构成，对EPS 的各个部件作了详细的介绍，并在此基础上分析了EPS 的受力情况，建立了控制系统模型，并研究了EPS 的安全性能； 2讨论了EPS 的三种控制方式，提出了控制策略，并讨论了其中三个关键模块的作用：预估模块包括对电机转速和方向盘角速度的预估，助力控制模块以及回正模块； 3用B 样条插值方法进行EPS 助力曲线的设计，可按照用户的要求设计任意形状的助力曲线，以满足不同车型和不同用户的要求； 4研究了控制系统的硬件结构，以MC68HC908MR8 为核心设计了控制器，详细讨论了控制器的控制电路、驱动电路等；设计了控制系统的软件，给出了控制程序流程图，并对要点进行了详细的说明。

It is the first time that the expert control theory is applied to the blasthole drill control described in the paper, where the expert control structure and strategy for blasthole drill control are studied. At last, an integrated software for the expert control is compiled with Borland C++4. 0 under the operation system of Windows95. It includes the following functions: the simulation for control theory and control structure, the realization of the blasthole drill control.

作者用Borland C++4.0在Windows95环境下编制了专家控制的集成软件系统，一方面对控制方案及算法进行了仿真研究，另一方面针对YZ-55型牙轮钻机的实际工况设计了软件控制功能；并按照牙轮钻机钻进控制的专家控制体系与控制策略，在实验室对控制算法与控制硬件系统进行了实验验证。

Linkage mechanism of study. Forepart all gather be linkage mechanism structural analysis and agency designer. In recent years so emphasize in kinetic synthesis dynamic and motility analysis. So text needle towards inquire into slider four-bar linkage mechanism agency positioning control.Research emphases are as PID control, fuzzy control, Fuzzy sliding mode control three kinds of controllers for control core. Permeate practical mechanism to positioning control to function. Simple exertion market vends signal extract card (PCL-833) and multi-function card (PCI-1711). Make it make signal extract and bring forth exportation control voltage. Will AC servo motor turn signal, as positioning system point of angle sensor. Reach to slider four-bar linkage mechanism servo positional control research.

连杆机构的研究，早期都集中在连杆机构的结构分析和机构设计，近年来也多著重於运动及动力分析上，因此本文就是针对於探讨滑块四连杆机构的定位控制，研究重点是以PID控制、模糊控制、模糊顺滑模式控制三种控制器为控制核心，透过实际的机构达到控制定位的功能，运用市面上贩卖的讯号撷取卡(PCL-833)和多功能卡(PCI-1711)，使其对讯号做撷取和产生输出控制电压，将AC伺服马达的转动讯号，作为定位系统的角度感测器，达到滑块四连杆机构伺服定位控制的研究。

This thesis focuses on the control scheme and dominated ideas of the painting automatic control system. The system adopted inductance near-switch and digital plate to check the location and shape of steel and based on S7-200PLC to control the call-off of a electronic- controlled valve, thus achieving automatic painting.

本文的重点在于喷漆控制系统的控制方案与思路，系统采用电感式接近开关和数码盘来检测钢板的位置和形状，以S7-200PLC为核心对电控阀进行通断控制，从而实现自动喷漆。

Our company main products has: IC integer machine; IC legs cut machine; IC grinding machine word; Automatic Tube Forming Machine crystals; electromagnetic, pneumatic machine parts; automatic bulk, loaded with parts cut legs, molding machine ; in bulk, with mounted machine resistance; jumper machine; electric crystal automatic molding machine; V-CUT substrate folded plate machine; automatic feed plate; hand solder immersion heaters; PCB Units cars, trolleys and block tin, the ordinary anti - welding kit aircraft series Reflow Solder Products.

本公司主要产品有：I.C整型机；IC切脚机；IC磨字机；自动管装晶体成型机；电磁式、气动式零件成型机；全自动散装、带装零件剪脚、成型机；散装、带装电阻成型机；跳线机；电晶体自动成型机；V-CUT基板折板机；自动送料盘；手浸式焊锡炉；P.C.B台车、手推车及挡锡条、金手指防焊套、流焊架等系列防焊产品。

Now the company is moving in the direction of mechanical and electrical integration, in recent years has produced a series of advanced ASCF automatic backwash filter, FJG automatic double-barrel anti-washing fine filter, QN automatic Kneader, JP Series Automatic mixed variety of liquid emulsion and other electromechanical integration equipment.

现在本公司正朝着机电一体化的方向发展，这几年先后生产了先进的ASCF系列全自动反冲洗过滤器，FJG全自动双桶式反冲洗精细过滤器，QN全自动捏合机，JP系列全自动多种液体混合乳化机等机电一体化设备。

Company's main products are Jinjia microcomputer-automatic machine, Jinjia PS version of microcomputer-automatic version and a microcomputer automatic Jinjia PS version Shaiban Ji Jinjia microcomputer automatic version of baked version of PS machine, Jinjia microcomputer replicator , Light Desk, density meters, Phototypesetter, film, PS version, and so on the plate; agent import-machine, machine-version, Shai Banji, DTP, CTP, and other printing equipment, such as plate-making equipment.

公司主要产品有金佳微电脑全自动冲片机，金佳微电脑全自动PS版冲版机和金佳微电脑全自动PS版晒版机金佳微电脑全自动PS版烤版机、金佳微电脑拷贝机、光台、密度计、照排机、菲林、PS版等制版材料；代理进口冲片机、冲版机、晒版机、DTP、CTP等印刷设备等制版设备。

This paper disertation explores on modeling and automatic recognition of NP in Russian sentences in light of Natural Language Processing, including linguistic foundation in the course of modeling, modeling of NP, multilevel description of models, modeling of AP with patulous components and automatic recognition of NP. In the process of recognition attention is paid to theoretic precondition of automatic recognition of NP, combinational rules of models, boundary mensuration of NP, automatic recognition of NP with postpositive attributes.

本文从自然语言处理的角度研究俄语中NP构句块的模式化和自动识别问题，内容涉及NP构句块模式化的语言学基础、NP构句块的模式化及模式的多层级、多平面形式化描写(包括带有扩展模式形容词的模式化)、NP构句块自动化处理，包括NP构句块处理的理论前提、模式组配规则、NP构句块的边界测定、带后置定语的NP构句块识别等。

Its SuperGraph technology architecture provides the following features: 3D visualizations, 3D modifications, plugin support, support for clusters and navigation, automatic graph drawing, automatic clustering of graphs, automatic selection of elements, and automatic coloring of elements according to a metric.

它的SuperGraph技术体系提供了下列功能：3D可视化，3D修改，插件支持，支持群集和导航，自动图像绘制，自动图像群集，自动选择元素，以及根据一个尺度自动为元素上色。

Have a plant area of 6000 square meters, with four-color, two-color Roland printing presses, automatic die-cutting machine, automatic machine, automatic paper mounting machine, grinder, folder gluer, such as a set of printing equipment, in the design of the production the better film, plate skilled personnel, computer and automatic punching machines and other copy-plate equipment, able to exert the maximum effect of the printing.

拥有厂房面积达六千平方米，拥有四色、双色罗兰印刷机、自动模切机、自动过胶机、自动裱纸机、磨光机、糊盒机等一整套印刷设备，在设计制作菲林上更胜一筹，技术精湛的制版人员，电脑和自动拷贝冲片机等制版设备，能最大限度的发挥印刷的效果。

After explaining total design of automated test system for microcircuit , the thesis introduces GPIB standard .

文章在说明了微电路模块自动测试系统的总体设计后，对GPIB标准进行了介绍。

He interceded in my behalf.

他替我说情。