查询词典 acceleration note

A new algorithm,which is called " weighting method of compensation " for exponential curve of acceleration and deceleration in CNC,is developed.

提出了数控系统中一种新的指数升降速控制曲线算法-加权补偿法，该算法用加权平均及权值修正技术，解决了数控系统中指数升降速控制曲线不能任意动态调整的难题。

The trend is defined by a specific type of exponential acceleration in the market.

这一趋势在市场中由一个特殊形式的指数加速度表现出来。

With the acceleration of industrialisation and urbanization in china ,more and more land was expropriate .

随着我国工业化和城市化进程的加快，征占农村土地的力度越来越大，失地农民越来越多。

Through detailed analyzing some influencing factiors of sand liquefaction, seven parameters were selected as assessment indexes. They are earthquake magnitude, peak ground surface acceleration, standard penetration value, specific penetration resistance, relative compaction, average particle diameter, and water table. The extension assessment model has been established that was applied to assessment of sand liquefaction potential. The model had been trained by the historical data and has been assessed in virtue of sand liquefaction from the historical data by simulating, and got a excellent result. After introduction of the support vector machine theory, this paper established the assessment model of sand liquefaction based on the support vector machine, and assessed in sand liquefaction from virtue data of some fields in home and overseas with the tool Libsvm, which was programmed based on the support vector machine theory. And got a good coherency between the assessement results and the actual liquefaction.

在详细分析影响砂土液化因素的基础上，选取了震级M、地面最大加速度g_、标准贯入击数N_(63.5)、比贯入阻力P_s、相对密实度D_r、平均粒径D_(50)、地下水位d_w等7个参数作为评价指标，建立了砂土液化势的可拓评价模型，并对历史数据进行仿真评价，取得了较好的应用效果；在对支持向量机的理论进行介绍后，本文建立了基于支持向量机的砂土液化势评价模型，并利用在基于支持向量机理论的Libsvm软件，对若干国内外场地的现场实测数据进行了评价，评价结果与现场表现基本上一致。

Taking the seismic acceleration response and horizontal bent angle as external forces, a simplified seismic calculating method considering train-bridge-earthquake interaction is proposed.

提出了以地震加速度响应和桥梁线路水平折角为外力的分阶段式考虑车—桥体系地震相互作用的简化抗震计算方法。

1While launching machine Dai soon suddenly accelerate, if the transition spray bore to stop, especially the vacuum type carburetor appear a transition badly, hybrid once annoy sparse but clean a carburetor transition after turning off by oneself the bore then can smoothly start to launch machine behind, after start in response to steady mildly accelerate, as far as possible avoid nasty acceleration, the factitiousness result in transition bad.

当发动机怠速时突然加速，若过渡喷孔堵塞，特别是真空式化油器出现过渡性不良，混合气过稀而自行熄火后，清洗化油器过渡孔后便可顺利启动发动机，启动后应平稳柔和地加速，尽量避免急加速，人为造成过渡性不良。

The peak acceleration of the ground is very sensitive to the local variation of the stress drop on the fault plane.

5地面峰值加速度对断层面局部应力降的改变非常敏感，加速度值与应力降之间不是简单的线性比例关系。

The relationship among acceleration, road and running velocity was studying, and the research result offered the theory direction for future enhancement running test of self-propelled gun in the field.

其仿真试验通过强化试验路面上得到的不同车速下车辆驾驶员位置的垂直振动和水平振动加速度及其均方根值，解算出振动加速度与路面及行驶速度的关系。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work.Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。2。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work. Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted. It was found in our drop tests that the root cause of lead-free solder joints under drop impact was the combined effect of mechanical shock and PCB bending vibration.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。

Tom: You are right, he worked hard all the time.

你是对的。他一直都是努力工作。

Take shortcomings,failures,and mockings of others as commonplace and a drive to complete oneself,hold your own opinion over the evalution and disscution divested from others,afterwards sink into the state of eliminate mistakes if any or encourge oneself being not being influenced by the sayinngs of others or having no ideas to do.

把缺点、失败及别人的耻笑等看成是一种常事，当成完善自己的动力，对别人的评价和议论自己心中有主见，做到&有则改之，无则加勉&，不为人言所左右或无所适从。