- 更多网络例句与牙嵌式离合器相关的网络例句 [注：此内容来源于网络，仅供参考]
-
A new cylinder type forage cutter with high operation was designed and manufactured. Construction design and its performance parameters, helical angle of moving knife, setting height of fixed knife, overload protective device, throwing device and edge shape of fixed knife were analyzed. The results of test were as follows: optimal helical angle of moving knife was 20°, optimal setting height of the center of the cylinder above fixed knife was 20 mm, line speed of blower vane was 13.6m/s ,power consump...
通过对 93ZT - 5 0 0型滚筒式铡草机的设计研究，分析了滑切角、定刀配置高度、定刀刃角对铡草机性能的影响，并对机构设计进行了探讨，试验结果为：动刀的螺旋角为 2 0°；滚筒中心高于定刀 2 0mm ；抛送风机叶片线速度 13.6m/s ；开刃定刀比矩形定刀的功率消耗低 17.5 %；安全防护装置采用牙嵌式安全离合器；研究结果对滚筒式铡草机的设计和应用具有一定的参考价值
-
In this paper,the threshold of the automatic control system for the synchronous differential lock of off road vehicle is analyzed.With the cornering model of a three-axle vehicle,the response limit of the system is analyzed theoretically.Through the analysis of the mechanical strength and the engaging characteristics of the dog clutch,the maximum difference of rotation speed between two parts of the dog clutch and hence the upper activation limit of the system are calculated
本文阐述了越野汽车差速器同步锁止机构自动控制系统的组成和工作原理，分析了其控制门限；利用所建立的三轴汽车转向行驶运动模型，在理论上确定了越野汽车差速器同步锁止机构自动控制系统的响应界限；通过对同步锁止机构牙嵌式离合器强度和接合特性的分析研究，确定了牙嵌式离合器允许的最高转速差，从而确定了动作限值的上限
-
The selection rules for the angles of jaw clutch, the determination of the sup ply voltage for the magnet, the design of the control circuit to eliminate the so-called "striking jaw top" and the measures to reduce residual magnetism and the switching time are discussed. The code circuit designing method for the speed control of the spindle box in XHK 5140 machining centre is also described.
本文根据牙嵌式电磁离合器的使用情况，对离合器齿形角的选择原则、激磁电压的设计、消除顶齿的控制电路的设计，以及采用电容器放电消除剩磁和缩短断开时间等问题进行了讨论，最后介绍了XHK5140立式加工中心主轴用电磁离合器变速的译码电路的设计方法。
- 更多网络解释与牙嵌式离合器相关的网络解释 [注：此内容来源于网络，仅供参考]
-
jaw clonus：颌阵挛
jaw chuck 颚式夹头,爪式卡盘,齿卡盘 | jaw clonus 颌阵挛 | jaw clutch 颚式离合器,爪式离合器,牙嵌式离合器,爪型离合器=>かみあいクラッチ
-
dodder transmission：菟丝子传染
dodder 菟丝子 | dodder transmission 菟丝子传染 | dog clutch 牙嵌式离合器
-
friction clutch：摩擦式离合器
牙嵌式离合器 Jaw clutch | 摩擦式离合器 friction clutch | 闸带离合器 brake-band clutch
-
square jackscrew：方形起重螺杆
square indexable carbide milling cutter insert 方形可转位铣刀片 | square jackscrew 方形起重螺杆 | square jaw clutch 方齿牙嵌式离合器
-
slipping switch：滑动式开关
slipping contact detector 滑触检波器 | slipping switch 滑动式开关 | slipping toothed electromagnetic clutch 牙嵌式电磁离合器
-
buttress thread form：锯齿形螺纹
矩形螺纹 square threaded form | 锯齿形螺纹 buttress thread form | 矩形牙嵌式离合器 square-jaw positive-contact clutch
-
jaw clutch：牙嵌离合器牙嵌离合器
jaw chuck 爪卡盘 | jaw clutch 牙嵌离合器牙嵌离合器 | jaw crusher 颚式破碎机
-
square jaw clutch：方齿牙嵌式离合器
square jackscrew 方形起重螺杆 | square jaw clutch 方齿牙嵌式离合器 | square law condenser 平方律可变电容器
-
spiral jaw clutch：螺旋面牙嵌式离合器
2613. spiral jacket ==> 螺旋式夹套 | 2614. spiral jaw clutch ==> 螺旋面牙嵌式离合器 | 2615. spiral-jaw clutch ==> 螺旋爪离合器
-
spiral jaw clutch：螺旋爪离合器
2614. spiral jaw clutch ==> 螺旋面牙嵌式离合器 | 2615. spiral-jaw clutch ==> 螺旋爪离合器 | 2616. spiral jaw coupling ==> 螺旋形爪式联轴节