- 更多网络例句与正半轴相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The stress and radial displacement will increase with the increment of half cone angle and lead.
螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。
-
The max stress and the max radial displacement of conveyor is also proportional to the square of rotational speed. With the decrease of the blade thickness, both the stress and axial displacement of conveyor increase rapidly. The stress and radial displacement will increase with the increment of half cone angle and lead.
螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。
-
In infinite dimensional RDS, different to finite case, the cocycle can be usually considered only in the positive half-time line.
无穷维的随机动力系(来源：ABd454C论文网www.abclunwen.com)统和有限维的相比，其中的cocycle往往只能定义在正半时间轴上，为此我们首先对无穷维半动力系统进行了负向延拓，使得在负半时间轴上也有定义。
-
The semi-low normal distribution membership function of fatigue limit is determined, and the anti-fatigue fuzzy reliability compute formula of rotor is deduced. The fuzzy reliability model of rotor anti-fatigue is set up. Taking an internal shaft of the rotor of aero electric generator for an example, its reliability design can be realized by adopting the anti-fatigue reliability design theory presented in the dissertation.
首次确定出了疲劳极限降半正态分布形式的隶属函数，推导出了转轴抗疲劳的模糊可靠度计算公式，建立了转轴抗疲劳的模糊可靠性模型；以航空发电机转子内轴为例，对其进行了抗疲劳的可靠性设计，并用本文建立的抗疲劳的模糊可靠度计算公式，对其进行了模糊可靠性校核。
-
By Visual Basic 6.0 program, taken the distance between hole 200mm and buried depth 120～150mm as the optimization goal, the most optimum parameters range of the mechanism was obtained as follows: the initial angle between planet frame and the line formed from spraying-fertilizer needle-tip and planet wheel axle was -45°～-40°, the initial angular displacement of planet frame was 40°～50°, the distance between spraying-fertilizer needle-tip and the planetary gear axle center was 280～300mm, simultaneously, the semi-major axis of elliptic gear was 29.364mm, the teeth quantity was 23, the ratio of semi-minor axes and semi-major axis was 0.958, the radius of circular gear was 25mm.
对该机构进行运动学分析，建立了数学模型，以穴距200mm和入土深度120～150mm为寻优目标，应用Visual Basic 6.0软件编程得出满足机构运动要求的最优参数范围为：喷肥针尖和行星轮轴连线与行星架的初始夹角-45°～-40°、行星架初始角位移40°～50°、喷肥针尖与行星轮轴心距离280～300mm，此时椭圆齿轮长半轴29.364mm、齿数23、短半轴与长半轴比0.958，正圆齿轮半径25mm。
- 更多网络解释与正半轴相关的网络解释 [注：此内容来源于网络，仅供参考]
-
positive azeotrope：正共沸混合物
positive axis 正半轴,正轴 | positive azeotrope 正共沸混合物 | positive balance 正平衡
-
positive hemipyramid：正向半锥;正半锥体
"正向半正轴坡面","positive hemi-orthodome" | "正向半锥;正半锥体","positive hemipyramid" | "正光率体","positive indicatrix"
-
semi-latus rectum：半正焦弦
半渐近法 semi-iterative method | 半正焦弦 semi-latus rectum | 长半轴 semi-major axis
-
orthodiagonal：正轴
正轴 ortho axis | 正轴 orthodiagonal | 正轴半锥 orthohemipyramid