- 更多网络例句与摆轴相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The kinematics of precision centrifuge isanalyzed in Chapter 2 adopting Homogeneous transformation and vector analysis.The calculating formulae of centripetal acceleration generated by precision centrifugeand acceleration acting on input axis, output axis and pendulous axis of accelerometerare deduced in theory under various conditions.
论文第2章首先用齐次变换法和矢量分析法对精密离心机的运动学进行了分析，从理论上推导出离心机产生的向心加速度的计算公式，以及各种条件下作用在加速度计输入轴、输出轴和摆轴上的加速度。
-
Since the rocking of the nipper shaft causes the nippers to move backward and forward through a series of links, the original position of nipper frame is altered when changing the detaching distance, resulting in the change of other process parameters of the comber.
由于精梳机的钳板摆轴传动钳板的方式都为四连杆机构，在进行落棉隔距的调整时，改变了连杆的初始位置，因此精梳机的其它工艺参数也随之改变。
-
Introduction is made to a new blueprint preparation of nipper mechanism on the combing machine .
介绍了一种和传统精梳机相区别的精梳机钳板机构的新方案设计，该钳板摆轴传动机构采用具有停歇功能的共轭凸轮机构。
-
The shaker includes a dual mass flywheel and the rotate and pendulum driven mechanism; in the rotate and pendulum driven mechanism, the rotary cylinder body of the rotatable hydraulic rotary cylinder (8) is connected with the sub flywheel (15) connecting with the main flywheel (13) and a rotary cylinder shaft (4) at the same side through a transmission sleeve (11) connecting to the rotary cylinder right end cover (9); a torsional transducer (10) and a turbulence iron core of an angular sensor (12) are arranged on the sub flywheel shaft, a winding of the angular sensor is positioned on the transmission sleeve fixedly connected with the main flywheel.
该激振器包括双质量飞轮及其旋转和扭摆驱动机构；所述旋转和扭摆驱动机构，其旋转液压摆缸(8)的摆缸体通过与摆缸右端盖(9)相连的传动套(11)，在同侧与主飞轮(13)和与摆缸轴(4)相连的次飞轮(15)相连接；扭矩传感器(10)及摆角传感器(12)的扰流铁芯装在次飞轮的轴上，摆角传感器的线圈装在与主飞轮固连的传动套上。
-
For guaranting the centre of oscillating axle in oscilla tor head being coincident with the centre of hone 's arc surface and centre of raceway curvity, JFX series optical diopters are adopted for adjustment.
在球轴承套圈沟道超精时，为保证振荡头摆轴中心、油石圆弧面中心和沟道曲率中心三者重合，采用JFX系列光学瞄准器具有很多优点，文中介绍了该仪器的光学原理、使用方法和注意事项等。
-
The influence of the excursion of the mass center of the torsional vibrating system of the three-string pendulum on the measurement of the moment of inertia is analyzed. A criterion for the mass center of the torsional vibrating system to be in alignment with the central axis of the three-string pendulum and a practical method to measure the moment of inertia of a body about a noncentral axis of mass using the three-string pendulum are proposed.
分析了三线摆扭振系统质心偏移对转动惯量测试的影响，给出了扭振系统质心与三线摆中心轴对齐的判别准则和用三线摆测定物体对非质心轴转动惯量的工程实用方法。
-
Products factory operators; Steyr, Steyr Wang, Hao Wo main bridge shell rear axle, bearing blocks, cross the bridge cover, Steyr wheel shell, shift cylinder, rear axle sudden yuan, ZF Clutch fork shaft, swing rod, before and after the brake hub, Steyr various separation fork, gear room covered ,67-68 pulley, bridge sudden yuan, steel plate, parallel to shell axis, double-H shift shaft , 0503 Steyr-axis between the shell bad, bad Steyr 0198 Inter-axis shell, oil seal and seat, steel plate before and after the hanging ears, rear wheel, shift box assembly, double H shift rocker, one, two block I. block F99588, shift box casing, drive shaft telescopic forks, steel slide, shift cylinder, a variety of connecting plates, gearbox sudden yuan, three, blockIntroduction F99589, Steyr cylinder cover, double-H shift dial head, adjust the lever fork, wheel cover, FL clutch fork, FL Clutch fork shaft, Steyr after the output shaft bearing support, flywheel shell, fork and seat connection, Steyr Cylinder Head,ácover ,67-68 water pipe joints, rear brake camshaft bracket, rear axle minus the main shell, minus the shell of the main bridge, bearing seat, adjust the lever forks, brackets, brake lane joystick arm, gearbox sudden yuan, clutch pedal arm, oil block at the end of care, single head, double-headed rocker, gear room covered, decelerationround, adjust the lever forks, shift box casing, double H shift dial head, Double H shell, gear room covered, separation lever plate before and after the hanging ears, double-H shift shaft, decelerationround,áBushing, Steyr 10 file clutch shell, the bridge box, minus the shell after the main bridge , Bearing Block, the bridge cover, Steyr wheel shell, shift cylinder, after the sudden the bridge element, ZF Clutch fork shaft, swing rod, steel slide, shift box casing series products .
本厂经营产品；斯太尔，斯太尔王，豪沃后桥主桥壳，轴承座，过桥箱盖，斯太尔轮边壳，换挡汽缸，后桥突元，ZF离合器拨叉轴，摆杆，前后制动毂，斯太尔各种分离拨叉，齿轮室盖，67-68皮带轮，中桥突元，钢板垫板，平行轴壳，双H换挡轴，斯太尔0503轴间差壳，斯太尔0198轴间差壳，油封及座，钢板前后吊耳，后轮毂，换挡盒总成，双H换挡摇臂，一，二挡导块F99588，换挡盒套管，传动轴伸缩叉，钢板滑座，换档汽缸，各种连接盘，变速箱突元，三，四挡导块F99589，斯太尔汽缸盖，双H换挡拨头，杠杆调整叉，轮边盖板，FL离合器拨叉，FL离合器拨叉轴，斯太尔输出轴后轴承座，飞轮壳，连接叉及座，斯太尔汽缸盖（欧II，平衡轴盖板，67-68水管接头，后制动凸轮轴支架，后桥主减壳，中桥主减壳，轴承座，杠杆调整叉，托架，行车制动操纵杆臂，变速箱突元，离合器踏板臂，油底托块，单头，双头摇臂，齿轮室盖，减速轮垫片，杠杆调整叉，换挡盒套管，双H换挡拨头，双H壳体，齿轮室盖，分离杠杆，钢板前后吊耳，双H换挡轴，减速轮垫片，平衡轴衬套，斯太尔10档离合器壳，过桥箱，后桥主减壳，轴承座，过桥箱盖，斯太尔轮边壳，换挡汽缸，后桥突元，ZF离合器拨叉轴，摆杆，钢板滑座，换挡盒套管等系列产品。
-
The result indicates that the diameter of escape wheel addendum, center distance of escape wheel and pendulum have their significant influence on the timing of clock mechanism.
结果表明，擒纵轮齿顶圆直径与擒纵轮轴与摆轴中心距对钟表机构计时的散布影响较大。
-
An anti-rotation reciprocating drive apparatus for a reciprocating saw utilizes a wobble plate assembly that includes a drive shaft and an elongated arm with an interface structure for engaging a spindle.
一种利用摆板组件的往复锯的防旋转往复驱动装置，摆板组件包括驱动轴和带有为连接心轴的接触面结构的细长臂。
-
In the pump body installed a stator swing span and a swing span rotation shaft, the swing roller bearing on the stator swing span connects with an end of the stator mount, the other end of the stator mount connects with the stator; on the plunger connecting rod sliding boot installed a static pressure balance chamber, the holding rings are arranged on the two sides of the plunger connecting rod sliding boot which has a fit clearance with the holding rings; the rotor rotates the stator simultaneously via the plunger piston; the needle roller bearings are arranged on the two inner circles and fit with the port axle.
在泵体内安置有定子摆架和摆架转轴，位于定子摆架上的摆架滚子轴承与定子托架的一端配合联接，定子托架的另一端与定子相连；柱塞连杆滑靴上设有静压平衡室，柱塞连杆滑靴两侧设有保持环，柱塞连杆滑靴与保持环有一定的配合间隙；转子通过柱塞带动定子同步旋转；在转子内圆两端设有滚针轴承，滚针轴承与配流轴配合。
- 更多网络解释与摆轴相关的网络解释 [注：此内容来源于网络，仅供参考]
-
axis of rotation：摆轴;旋转轴
axial vibration,轴向振动 | axis of rotation,摆轴;旋转轴 | axix of strain gauge,应变计[片]轴线
-
Bled：双级法兰式立装专用电动机直联型摆线针轮减速机
BWED双级脚板式卧装普通电动机直联型摆线针轮减速机 | BLED双级法兰式立装专用电动机直联型摆线针轮减速机 | XW脚板式卧装双轴型摆线针轮减速机
-
COAX：同轴
在DA-1716kit的电路板上,我们利用一个Jumper(跳针)来切换同轴(COAX)或光纤(OPTI)输入端. 当使用同轴时,请将红色的套帽摆在中点与COAX间;使用同轴时,则应该将红色套帽摆在中点与OPTI之间.
-
swing hammer mill：摆锤式磨机
swing hammer crusher 摆锤式破碎机 | swing hammer mill 摆锤式磨机 | swing hanger crossbar 摇枕吊轴
-
pendulous axis：摆轴
pendulosity 摆性 | pendulous axis 摆轴 | pendulous gyro accelerometer 摆式陀螺加速表
-
axial runout：轴向偏摆[跳动]
axial play 轴向间隙 | axial runout 轴向偏摆[跳动] | axis of rotation 旋转轴
-
axial runout：轴向偏摆
axial play 轴向间隙 | axial runout 轴向偏摆 | axis of rotation 旋转轴
-
axial runout：摆T,轴向偏转
轴线的平面 axial plane | 摆T,轴向偏转 axial runout | 轴向剖面 axial section
-
balance staff：摆轴
摆钟 pendulum | 摆轴 balance staff | 半成品 ebauche
-
bob pendulum：连叉摆(摆杆直接连接在叉轴上, 而摆锤下接用螺纹与摆杆连接的摆)
bob off || 骗离去 | bob pendulum || 连叉摆(摆杆直接连接在叉轴上, 而摆锤下接用螺纹与摆杆连接的摆) | bob up like a cork || 东山再起