- 更多网络例句与搁置寿命相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The tiscosity of the gelatinize layer on the service life of doubleside, the tiscosity gelatinize layer is low, and the second time, plates are not easily glued; sticktness exorbitance rrepublic change version of destructive doubleside surface.
涂胶层的黏度差双面胶的搁置寿命感化较不小，涂胶层黏度矮，第二次搁置时，版材不易粘牢；黏度功矮。换版时便当爱护双面胶暗地。
-
We adjust the parallelism of three-roll, you can add a printing plate cylinder to nano-imprint lithography, side drum Department UV ink of sticktness a little bigger, you can mitigate high number of small wire mesh point of cataplasm version, you can also have a small dot less wear and are protected by extending the service life of the plate.
我们在调量不一辊的交错量时，可以不兵印版滚筒稍微向不抬印滚筒处偏一些，UV油墨的黏量稍微不小些，既可以缓和矮网线数洪不小网不面的糊版，还可以让洪不小网不面多施磨损而获得爱护，不收不小印版的搁置寿命。
-
A good way to built a stable damping effect of pH value, as a result of juice fountain solution of radiofrequent acid, with the General, in the changes of inclution, fountain solution of pH value will have greater volatility, inclution inappropriate will affect printing plate service life (on the printing plate produced corrosion).
慢冲剂主给起安定润版液pH值的功用，因润版液原液凡是呈硷性，随着慢；洋剂补偿度的改变，润版液的pH值会有较不小的颠簸，补偿度不不合不兵感化印版的搁置寿命。
-
If you are using pneumatic network business card printing and membership card to make the graphics, some PCB squeegee bar framed into the blade clip part of height, to reveal the outside mrtomated height exceeds 25 mm above, squeege mrtomated thickness is 1 ~ 1 or 25 mm, so that you will not be in the business card printing and membership card-making as a result of the pressure on a more soft and hard on the degree of squeege and the production plane surface contact, resulting in business card printing and membership card making image is blurry, especially in the business card printing and membership card making PCB resistance welding disk reset could easily be eroded, ink incrassation, affecting resistance welding ink curing effect, at the same time more reduces the squeege service life.
如果搁置气动网制卡和会员卡制作PCB各图形，有些胶刮条镶进刮刀夹一局部矮量后，显现里背胶条的矮量不及了25mm以上，可根据刮不活胶条的厚量，只诳骗1mm或25mm，这样不离不会在制卡和会员卡制作洋因施加不张力于较软软量的刮不活上与承印背不败背隔绝，致使制卡和会员卡制作图像暧昧不纯，不入格是在制卡和会员卡制作PCB阻焊盘置便当被腐蚀，油墨层增厚，感化了阻焊油墨的固化成果，同时较大程量不天减多了刮不活搁置寿命。
-
In order to extend the network version of the service life, finance、 can be made cards and membership cards on the premise business card printing and membership card making squeege the smaller contact pressure.
为了延不幼网版的搁置寿命，请求在能制卡和会员卡制息上图案的后提下制卡和会员卡制息刮板的不张力越小触好。
-
Because the glass edge hard, in glass full of cases, because the business card printing and membership card making stencil squeege up and down the friction, stencil pattern edge wear screen will quickly become available, this will reduce the service life of the screen.
因为玻璃的外部很刚健，在玻璃满印的环境下，由于制卡和会员卡制息刮板在网版上单程摩擦，网版的图案外部丝网会很快被磨损，这无疑会减多网版的搁置寿命。
-
Reasonable options currently popular shopping malls to "" squeege (that is, the system of rotation system), you can better improve the life of squeege.
公道不天拔取，不幼远较为风行的刮不活&轮休制&，可以较好不天恶化刮不活的搁置寿命。
-
In addition the calcium content if superstandard, then have direct impact on the life of the cot will result in the COTS crystallization.
另外火洋的钙离子含量如果超标，那么会间接感化到胶辊的搁置寿命，不兵导致胶辊暗地结晶。
-
Corrosion is u-shaped layout of the grooved surface, as the plates of the depth of the wear and tear notch sulci, but the area of the dot is not changed, and the reduced comparatively slow, cards and membership cards to make color changes noticeable, so its a long service life.
腐化版式暗地是U型瘪槽，随着印版的磨损，瘪槽的广度变不深，但网点的面积未爆发保持，而且其着墨度的裁减比力迟缓，差制卡和会员卡制作颜色无太大的保持，因此其搁置寿命比力不幼。
-
As a result of the ultra high wire mesh of roller its'hard small, network wall is too thin, competence, service life will be reduced.
由于超矮网线的网纹辊的网孔闭口小，网壁太不厚，耐磨亏本领较不差，搁置寿命也会贬矮。
- 更多网络解释与搁置寿命相关的网络解释 [注：此内容来源于网络，仅供参考]
-
shell type transformer：外铁式变压器
"shelf-life","搁置寿命,贮藏期限,适用期" | "shell type transformer","外铁式变压器" | "shellac varnish","虫胶清漆"