- 更多网络例句与扭转变形相关的网络例句 [注：此内容来源于网络，仅供参考]
-
For example ,if the active part of a shaft is 40 in .1deg of torsional deflection would be permitted .In some applications ,the angle of twist must be smaller than this .
例如，如果活跃的一部分是40 。1deg轴扭转变形，将允许在某些应用场合，角的扭必须小于这个。
-
This paper analyzes the factors that affect the performance of silicon oil fan clutch and the key configuration.A kind of silicon oil fan clutch has been developed,performance and experimental data of silicon oil fan clutch are summarized through bench testing.The test results show that the optimized clutch can make a response to temperature and has less consumption of power.
硅油风扇离合器不仅可以减少发动机有效功率的损耗，改善发动机的经济性，提高发动机寿命，而且能有效的降低发动机噪声，具有广阔的应用前景[1]。1结构及工作原理硅油风扇离合器是用硅油作介质，利用硅油高粘度的特性来传递转矩，其结构如图1所示，当发动机负荷增加时，水温升高，从散热器吹来的热空气使双金属感温片受热而扭转变形，带动阀销一起转动并通过感温片变形量的大小控制进油阀开度。
-
So we can analyse the stability of lattice structure as solid web beam without change its geometry dimension. The out-of-plane stability of bending beam, which is made up with 2 beams and loaded by non-directional force, is studied.
对两节梁组成的弯曲梁在非保向力作用下的平面外失稳问题进行了研究，通过建立每节梁临界状态下弯曲和扭转变形微分方程，根据杆件变形的边界条件以及杆件之间的变形协调关系，得出了一端固定一端悬臂的弯曲梁在非保向力作用下平面外失稳的特征方程。
-
The effects of shear deformation of ...
分别考虑了剪力墙的剪切变形和结构的扭转变形对计算结果的影响。
-
Analyzes and calculates the stress and torsional deflection of large transformers such as DEP-240 MVA/500 kV,SEP-720 MVA/500 kV,etc.influeced by axial current component of low voltage spiral windings.Gives the distribution rules of torsional stress of unit length and displacement following windings height.Provides the reference for optimization design of large transformer.
对DEP-240 MVA/500 kV、SEP-720 MVA/500 kV型大型电力变压器低压螺旋绕组在轴向电流分量作用下产生的应力及扭转变形问题进行了分析计算，给出了低压螺旋绕组单位长度扭转应力及位移沿绕组高度的分布规律，为大型变压器的优化设计提供了参考依据。
-
If this lateral support is removed,as may occur in an untimbered excavation,the likely outcome is a shear slip in the soil beneath the footing,taking the footing into excavation.
如果这种压力不存在，例如在一个没有被木桩填实的洞中，很有可能会引起地基的剪切变形或者扭转变形，趋向于使地基填住那个空洞。
-
The torsional distortion and the torsional rigidity of the cross axle type universal shaft are calculated by using the three-dimensional finite elements method.
运用三维有限单元法对十字轴式万向联轴器的扭转变形和扭转刚度进行了分析计算。
-
The results show that when the tunnel is excavated in the single soil layer, the vertical displacement is similar as settlement. When the tunnel is located at the typical soil layers, there are torsions as well as the settlement.
分析结果表明，在单一土层中由于土体的约束作用，结构产生的位移以整体沉降为主，在成层土体中除产生一定的整体变形外还伴随一定的扭转变形。
-
The influences of length-to-thickness ratio, material anisotropy and torsions effect on natural frequencies and buckling loads were also investigated.
分析中同时考虑了一阶和高阶横向剪切变形、转动惯量、细长比、各向异性、扭转变形等多种因素对组合梁固有频率和屈曲载荷的影响。
-
With a given bending and torsion deformation of wing tip,the whole transformed geometry can be estimated.
机翼的平面形状可看作由多个梯形组成，机翼弯曲变形为三次函数，扭转变形为一次函数。
- 更多网络解释与扭转变形相关的网络解释 [注：此内容来源于网络，仅供参考]
-
turbulent displace：变形置换
--transform变换 | --turbulent displace变形置换 | --twirl扭转
-
Hooke's Law：定律
但在实际研究中不可能会有符合这些条件的材料,所以须要各种理论与实际方法对材料进行实验比较. 材料在机构中会受到拉伸、压缩、弯曲、扭转及其组合等变形. 根据胡克定律(Hooke's law),在弹性限度内,物体的应力与应变成线性关系.
-
Racking：倾斜,变形,船体扭转变形
quotation 报价单 | racking 倾斜,变形,船体扭转变形 | radiography X射线探伤
-
radiography X：射线探伤
racking 倾斜,变形,船体扭转变形 | radiography X射线探伤 | rake 倾斜
-
scissors：剪刀
5-1-14 剪刀(Scissors)工具 5-1-15 美工刀(Knife)工具 5-1-16 修整 5-1-17 一般修整 5-2 液化变形工具 5-2-1 弯曲(Warp)工具 5-2-2 扭转(Twirl)工具 5-2-3 收缩(Pucker)工具 5-2-4 膨胀(Bloat)工具 5-2-5 扇形扭曲(Scallop)工具 5-2-6 晶体休(Crystallize)工具 5-2-7 折皱(Wrinkle)工具 5-3 封套(Envelope)变形 5-3-1 使用默
-
Twirl：扭转
5-2-2 扭转(Twirl)工具 5-2-3 收缩(Pucker)工具 5-2-4 膨胀(Bloat)工具 5-2-5 扇形扭曲(Scallop)工具 5-2-6 晶体休(Crystallize)工具 5-2-7 折皱(Wrinkle)工具 5-3 封套(Envelope)变形 5-3-1 使用默认封套变形 5-3-2 使用封套变形网格 5-3-3 使用对象进行封套变形 5-3-4 编辑封套变形 5-4 对象的变形 5-4-1 移动(Move)对象
-
stress concentrations：应力集中
4.6 Thermal Stress 热应力 | 4.7 Stress Concentrations 应力集中 | 5.1 Torsional Deformation of a Circular Shaft 圆轴的扭转变形