- 更多网络例句与工作台底座相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The base is equipped with an X-axis workbench, a Y-axis workbench and a microscope, a bonding head is arranged above the workbench, a liftable support is arranged on the base, the microscope is mounted on the liftable support and provided with a Z-axis stepping motor, and an automatic magnification regulating mechanism is arranged on the microscope.
在底座上设置有X轴工作台、Y轴工作台和显微镜，在工作台的上方设置有键合头，在底座上还设置有可升降支架，显微镜安装在可升降支架上并且在显微镜上设置有Z轴步进电机，显微镜上安装有放大倍数自动调节机构。
-
The table base with the table backand forward is Y. The spindle head going up and down is thedirection of Z axis feed. The Z motor takes with brake. when thepower is cut off, the motor stops in order to prevent the spindlehead fall down because of self-gravity.
工作台底座带工作台前后运动为Y轴方向。Z向进给为主轴头的上下运动，并且Z向电动机是带制动器的，当断电时，Z向刹紧，以防主轴头因自重而下滑。
-
The machine table in casting design with heavy ribbing is supported by a hydrostatic bearing design ( acc. to the principle pump per pocket ) in the machine base.
带加强筋结构的铸铁工作台由机床底座上的静压轴承支撑（通过静压油孔与主泵连接）。
-
The invention relates to a desk type drill machine for preventing drill head wreckage, comprises chassis, supporting post, operating board covered in middle of supporting post, cabinet and generator; cabinet is equipped with tension pulley pressure sensor, belt tension unit and pressure foil gage; tension pulley is compacted on driving belt of drill machine, pressure foil gage is installed on top bar of tension pulley, the pressure foil gage is in electric connection with input end of controlling circuit, output controlling end of controlling circuit is connected to power input end of generator.
本发明是防止钻头折断的台式钻床，包括底座、支柱、套在支柱中部的工作台、以及机箱和电机，机箱上设有张紧轮压力传感器，由皮带张紧装置和压力应变片组成，其中的张紧轮紧压在钻床的传动皮带上，压力应变片设在张紧轮的顶杆中，压力应变片与控制电路的输入端电连接，控制电路的输出控制端连接在电机的电源输入端中。
-
The table base with the table back and forward is Y.
工作台底座带工作台前后运动为 Y 轴方向。
- 更多网络解释与工作台底座相关的网络解释 [注：此内容来源于网络，仅供参考]
-
table base register：表格基地址寄存器,表式变址寄存器,表式基址寄存器
table base 工作台底座 | table base register 表格基地址寄存器,表式变址寄存器,表式基址寄存器 | table beet 菜用甜菜
-
bed：底座
使面板平整. 至于C、D各方式中是采用单边坡口或是双边坡口,应根据结构的实际情况而定. 4、焊接结构滑块(SLIDE)的设计5、焊接结构底座(BED)的设计6、焊接结构移动工作台(MOVING BOLSTER)的设计7、焊接结构立柱(UPRIGHT)的设计
-
table base：工作台底座
table balance ==> 托盘天平,架盘药物天平 | table base ==> 工作台底座 | table base register ==> 表格基地址寄存器,表式变址寄存器,表式基址寄存器
-
table base register：表格基地址寄存器,表式变址寄存器,表式基址寄存器
table base ==> 工作台底座 | table base register ==> 表格基地址寄存器,表式变址寄存器,表式基址寄存器 | table beet ==> 菜用甜菜