- 更多网络例句与夹紧螺母相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Based on the idea of the structure parametric design method, the parametric finite element model of drill chuck with complicated spiral surface character was established.'The related key technologies of drill chuck's strength analysis were discussed and solved, such as the contact analysis parameters selection, the boundary conditions and the load processing, ANSYS command一string building and so on.
本文采用结构参数化设计方法建立了含有复杂螺旋曲面特征的钻夹头参数化有限元模型；探讨和解决了钻夹头夹紧强度分析中夹爪与螺母接触分析参数的选择、约束边界和载荷处理、分析流程文件创建等关键技术问题。
-
Finger tighten the column nut until it starts to grab the column, and then tighten the nut an additional 1/4 to 1/2 turn so that the column can't be pulled from the fitting when gentle pressure is applied.
用手拧紧柱螺母直至其开始夹住柱子。再拧1/4-1/2圈，这样轻轻拉动时，柱子不会脱出来。8。
-
Circlips for shaft/hole; open grip rings; steel wire circlips; round wire snap rings; spring washers with internal teeth, external teeth, curve, wave; external tap round nuts, external tongue round nuts with long tap, external tongue round nuts with long tap and wing, etc; motorcycle accessories, auto transmission shaft rings, non-standard fasteners.
我公司按国际生产孔用挡圈，轴用弹性挡圈，开口夹紧挡圈，钢丝挡圈，DIN471 DIN472 DIN6799，特大挡圈200-800，厚度不限。各种内齿，外齿垫圈。鞍形，波形，推型弹性垫圈，各种规格型号的弹簧垫圈，不锈钢弹簧垫圈。以及单耳，双耳外舌园螺母等，摩托车配件，各种汽车传动轴卡簧及非标准件
-
Which is greater on locknuts, proof load, or clamp per equal diameter?
保证载荷或每等径夹紧力，哪个在锁紧螺母中最大？
-
For the upper and lower physical decomposition of the fuel pump, pump body can be placed, open side cover, remove the pump head fastening nut, remove the pump head, hand clamp plunger living roots, slowly out the plunger and spring cylinder fault, with clean petrol or diesel repeated washing, wash, after-loading complex (note the plunger into the regulation of regulation must fork arm), and alternately tighten pump head nut, rotating camshaft, oil pump pulled the handle to manipulate the review.
2对于上、下体能分解的喷油泵，可将水泵体平放，打开侧面盖板，卸下泵头紧固螺母，取下泵头，用手钳夹住柱塞根部，慢慢抽出故障缸柱塞和弹簧，用清洁的汽油或柴油反复清洗，洗净后装复(注意柱塞调节臂必须装入调节叉内)，并交替拧紧泵头螺母，转动凸轮轴，扳动油泵操纵手柄复查。
-
By mean of a clamping lever on the front of the apron, the split nut can be closed around the lead screw.
通过溜板箱前面的夹紧手柄可以使对开螺母紧紧包含丝杠。
-
C Pull cable through nut and sealing ring. To ensure tightly sealing performance, it is prohibition to pull thin cable through wide aperture sealing ring.
将电缆套上螺母、密封圈，套密封圈时，不要出现小电缆穿大孔密封圈的现象，以免无法夹紧密封，影响防护性能。
-
E Successively put sealing ring and screw in the accessory of steel tube and press the sealing ring to clamp the cable and seal it reliably.
依次将密封圈、螺母装入引入装置壳体内，并拧紧螺母压紧密封圈，使电缆可靠夹紧、密封。
- 更多网络解释与夹紧螺母相关的网络解释 [注：此内容来源于网络，仅供参考]
-
gib screw：调整楔用螺钉,夹紧调整螺钉
gib nut 翻边锁紧螺母 | gib screw 调整楔用螺钉,夹紧调整螺钉 | gib-headed bolt 扁头螺栓
-
tightening pulley：张力轮
tightening nut 拉紧螺母 | tightening pulley 张力轮 | tightening screw 夹紧螺钉,紧固螺钉
-
turn indicator：转变指示器
turf 泥煤 | turn indicator 转变指示器 | turnbuckle 夹紧螺母
-
turned bolt：车制螺栓
turnbuckle 夹紧螺母 | turned bolt 车制螺栓 | turner 车工
-
binding post nut：接线柱螺母
199. binding nut ==> 夹紧螺母,扣紧螺母 | 200. binding post nut ==> 接线柱螺母 | 201. Bingham fluid ==> 宾汉流体
-
binding head screw：扁头结合螺钉
197. binding bolt ==> 紧固螺栓 | 198. binding head screw ==> 扁头结合螺钉 | 199. binding nut ==> 夹紧螺母,扣紧螺母
-
clamp hose connection：用夹子夹住的软管连接
夹紧装置 clamp device | 用夹子夹住的软管连接 clamp hose connection | 紧固螺母 clamp nut
-
gib screw：调整楔用螺钉,夹紧调整螺钉
gib nut ==> 翻边锁紧螺母 | gib screw ==> 调整楔用螺钉,夹紧调整螺钉 | gib-headed bolt ==> 扁头螺栓
-
self-tightening locknut：自紧防松螺母
self-tightening lever clip ==> 自紧式夹杆 | self-tightening locknut ==> 自紧防松螺母 | self-tightening oil seal ==> 自紧油封
-
self-tightening lever clip：自紧式夹杆
self-threading shuttle ==> 自动穿纱式梭子 | self-tightening lever clip ==> 自紧式夹杆 | self-tightening locknut ==> 自紧防松螺母