- 更多网络例句与喂料相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The paper reports a new kind of feeding method using intermeshing helical roll for cold feeding rubber extruders.
提供了一种冷喂料橡胶挤出机新型螺旋啮合辊喂料方法。
-
In addition, the company兼营pin barrel cold feed rubber extruder, this product is the new generation of rubber extruder, can replace imported products, and old-fashioned extruder compared to pin barrel cold Feeding rubber extruder with an high degree of automation, out of capacity, low energy consumption units, plastic ranked lower temperatures, dense products with good quality high.
除此之外，公司兼营销钉机筒冷喂料橡胶挤出机，本产品是新一代橡胶挤出机，完全可以替代进口产品，和老式挤出机相比，销钉机筒冷喂料橡胶挤出机具有适自动化程度高、挤出能力大、单位能耗低、排胶温度低、制品致密性好、质量高等特点。
-
Combination with continuous feed screw geometry.
连续喂料，最好同连续喂料挤出机螺杆组合共同安装。
-
Clay and gypsum will be transported into plant by trucks and unloaded into different bins in the crushing station, and then fed onto crusher by speed-governable apron feeder. Crushed materials will be fed onto auxiliary materials stockyard by belt conveyor.
由汽车运入厂区的粘土、石膏等生产辅助原料，分别卸入破碎站料仓内，经料仓下可调速的板式喂料机喂入破碎机进行破碎，破碎后的物料由出料带式输送机转运至辅助原料堆场。
-
Stuffer pot adopts unique feeding head design, which ensures the complete matching of large quantity of filler incorporation and uniformity of threading, with high production of the complete machine.
喂料机筒采用独特的喂料口设计，保证了吃料量大、喂料均匀，与整机高产量完全匹配。
-
Injection molding feed of Fe-Ni-Cu-C alloy coarse powder with particle size of 60um was prepared, effect of rate of shear, temperature and proportion of powder and binder to rheological behavior of feed was studied, viscosity number of three kinds of feed in different temperature was measured by capillary viscosimeter strain sensitivity factor three kinds of feed with different component were compared.
制备了平均粒度为60m的Fe-Ni-Cu-C合金粗粉汁射成形喂料，研究了剪切速率、温度、粉末和粘结剂比例对喂料流变行为的影响，应用毛细管粘度计测量了三种喂料在不同温度下的粘度值，比较了三种不同成分喂料的应变敏感性因子的大小。
-
Finally, simulation software was developed with Visual C++ and Delphi for 2D molding analysis of MIM, which affords facilities for the quality forecast of 2D thin wall parts and optimal design of mold and process parameters. In the research of molding performance of MIM feedstock, for the shortcoming of capillary rheometry, it was propounded that using spiral mold test molding performance of feedstock, and a set of spiral mold was creatively designed with quickly exchange gates and closed mold cavity. With the spiral mold, an orthogonal experiment was made on getting regress equation of flow length L〓 of the heavy alloy feedstock. Then the rule of L〓 varying with Q〓, P〓, and ΔT〓 was discovered. Q〓 ranks first in the influence on process parameters of molding performance, P〓 and Δ T〓 second. Therefore the injection rate Q〓 should be controlled primarily to improve the flow performance of feedstock.
在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L〓的回归公式，揭示了L〓随Q〓、P〓、△T〓和S〓的变化规律，并得出工艺参数对成形性能影响的强度顺序为Q〓最大，P〓与△T〓其次，因而改善喂料流动性能应优先控制注射速率Q〓。
-
Moreover, this paper introduces the analysis and design of automation system of the production line at length, including the spot controlling unit, the central controlling unit, hardware and software, communication connecting and electricalcontrol. Also introduces the technique analysis and controlling method design of the raw material preparation, rotating kiln system and coal powder preparation. Describes the system design in detail, such as the main control interface, the system main interface, the system flow diagram, group start and stop, equipments selecting, emergency and fault reset, alarming picture, tendency picture, speed setting, raw material feeding, feeding operation, production reporting table and so on.
接着，论文对该生产线自动控制系统进行了详细地设计分析，包括现场控制部分、中央控制部分、软硬件部分、通讯连接部分和电气控制部分；对生料制备系统、回转窑系统和煤粉制备系统进行了工艺分析和控制方法的设计；并对系统主要控制界面，系统主界面、系统流程图、组起/组停、设备选择、故障复位、故障紧停故障消音、报警画面、阀门操作、趋势画面、转速设定、生料喂料、喂煤操作、原料喂料、生产报表等做了设计介绍。
-
Low level sensors can stop the sorter feed when the input hopper is nearly empty, and high level sensors can be used to protect against resort infeed hoppers overflowing.
当进料斗接近物料时，低料位传感器能中断色选机喂料，高料位传感器用来保护复选喂料斗物料的外溢。
-
In the research of visual simulation software development, in order to build the software system model and flow analysis algorithm based on Cross-WLF viscosity model, and realize functions such as pre-processor, solver, parameter regress, data management, graph operations, some advanced software methods as OOSE (Object Oriented Software Engineering) and UML were applied to set up user model, static model and dynamic model of MIM simulation software. These models describe system function, event flow, structure and relation of classes, object interaction, structure of database and I/O file format.
在MIM喂料注射成形性能研究方面，针对毛细管流变仪测试法衡量流动性能的不足，提出使用螺旋线模具测试喂料熔体的注射成形性能，创造性地设计了一套可快换浇口，模腔封闭的螺旋测试模，并在螺旋测试模上采用正交实验设计，得出了高密度重合金喂料流动长度L_m的回归公式，揭示了L_m随Q_m、P_m、△T_m和凡的变化规律，并得出工艺参数对成形性能影响的强度顺序为Qm最大，尸m与△几其次，因而改善喂料流动性能应优先控制注射速率Qm。
- 更多网络解释与喂料相关的网络解释 [注：此内容来源于网络，仅供参考]
-
cold feed rubber machine：冷喂料橡胶挤出机
cold fault 冷机故障 | cold feed rubber machine 冷喂料橡胶挤出机 | cold fertilizer 冷性肥料
-
feedbox：喂料箱
feedbackcontrol 反馈控制器 | feedbox 喂料箱 | feedcontrol 喂料控制器
-
hand round pass：手工喂料轧制的圆孔型
hand rounds人工操作轧制的圆钢 | hand round pass手工喂料轧制的圆孔型 | hand sampling手工取样、人工采样
-
feeding pross：喂料螺旋压榨机;(切纸机)送纸辊
feeding conveyer 送料运输机 | feeding pross 喂料螺旋压榨机;(切纸机)送纸辊 | feeding roll 喂料辊;送纸辊
-
refeed：重新喂料
refection 恢复体力 | refeed 重新喂料 | referable 可付呜的
-
rethread：修理螺纹 重新穿进 重新喂料 再通过
retgersite 镍矾 | rethread 修理螺纹 重新穿进 重新喂料 再通过 | rethreading 修理螺纹
-
scooping feeding device：勺式喂料机
scooper 斗式升运机 | scooping feeding device 勺式喂料机 | scooter 踏板车
-
feed guide：喂料导板
feed end 加料阀 | feed guide 喂料导板 | feed guide stop 给料缓冲装置
-
variable-speed feed roll：变速喂料辊
variable-speed chopper 变速斩波器 | variable-speed feed roll 变速喂料辊 | variable-speed generator 变速发电机
-
Star wheel feeder：星轮喂料机
链条刮板喂料机:Bar-flight-feeder | 星轮喂料机:Star wheel feeder | 波动辊给料机:Fluctuate Roller Feeder