welding seam

welding seam的基本解释

-

[化] 焊缝

与welding seam相关的网络例句 [注：此内容来源于网络，仅供参考]

In the research of image system, a image processing algorithm of welding seam is established on the basis of image math. model of structured light of Fourier-transformation of lens in space, and the image analyzing system based on the rule-model of the features of welding seam in 3D-space is also established which can meet the requirements of the auto-programming of welding parameters for arc welding robot in accuracy and reliability.

在焊缝图象系统的研制中，基于结构光空间付氏变换的光纹图象数学模型，建立了焊缝图象处理算法，并基于焊缝三维空间特征的规则模型，建立了焊缝图象分析系统，使焊缝检测与分析的精度和可靠性达到了弧焊机器人焊接参数自动规划及焊接路径自动规划的精度要求。

This paper gives a discussion on relation between shape,size and quality of welding seam ,and introduces the effect on liquidity of metal in molten bath and shape of molten bath from welding stress and the effect on size of welding seam from welding parameter and its technological factors.

论述了焊缝的形状尺寸与焊缝质量的关系，介绍了焊接中力对熔池金属的流动及熔池形状的影响、焊接参数和工艺因素对焊缝尺寸的影响，对焊缝缺陷产生的原因进行了分析并提出了预防措施。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

与welding seam相关的网络解释 [注：此内容来源于网络，仅供参考]

Shallow Coal Seam：浅埋煤层

电阻缝焊:resistance seam welding | 浅埋煤层:Shallow Coal Seam | 焊缝跟踪:Welding seam tracking

steep coal seam：急倾斜煤层

焊缝自动跟踪:Welding seam auto-tracking | 急倾斜煤层:steep coal seam | 多煤层开采:multi-seam mining

Tough coal seam：韧性煤层

焊缝识别:welding seam recognition | 韧性煤层:Tough coal seam | 复杂煤层:complex coal seam