triangulation station

triangulation station的基本解释

-

三角测量标点, 三角测量站, 三角点

与triangulation station相关的网络例句 [注：此内容来源于网络，仅供参考]

How to apply the triangulation principal being consist of outside triangulation and inside triangulation in the local increment triangulation algorithm is analyzed. A method of optimization while triangulation and a principal to judge whether the triangle is legal or not are established. Software design of this algorithm is done. At last, the calibrated result of field lens is presented.

采用了一种大规模散乱数据的空间划分方法及其相应的数据结构和编码方案，研究分析了在局部增量剖分算法中如何采用外连剖分和內连剖分相结合的剖分原则，确定了边剖分边优化和一种计算空间点到直线距离的简单方法来判断三角形是否合法的原则。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

Based on the two features of the Delaunay triangulation:maximum and minimum feature,empty circumcircle feature,in this article the procedure of building triangulation network needs three steps:creating boundary,building up the interior triangulation network,coping with the hole between the boundary and the interior triangulation network.

基于Delaunay三角网划分的两个特性：最大最小特性与空外接圆特性，论文构网过程分三步：生成边界，构造内三角网，对边界与内三角网之间的空洞进行处理。

与triangulation station相关的网络解释 [注：此内容来源于网络，仅供参考]

triangulation galloon：三角测量氧球

三角測量選點 triangulation reconnaissance | 三角測量氧球 triangulation galloon | 三角測站 triangulation station

triangulation network：三角测量网

triangularthread 三角螺纹 | triangulation network 三角测量网 | triangulation station mark 大地测量三角网台标记

Filling Station：加油站

加油站在美国的叫法有多种,直译成中文的有:汽油站(Gas Station)、燃料站(Fuel Station)、加油站(Filling Station)以及服务站(Service Station)等. 在美国公众中"服务站"(Service Station)已是一个琅琅上口的叫法,作为"加油站"的代名词被广泛认可和接受. .