阀盖

Its lower end cap on the drain plug is used to discharge valve in the fluid.

其下部端盖上的螺塞，是用来排放阀中的积液。

Nut series: Hex flange nut, nylon nut, with sets of teeth, K nut, square nuts, butterfly nuts, cap-type nut, bolts, plum-type shrapnel, Groove nut, welding nut, thin nuts, both inside and outside the dental cone mother, Nut, the plastic nut, valve nut, pipe joints, back caps, sleeves and other metal products.

螺母系列：六角法兰螺母、尼龙螺母、内套牙、K螺母、方螺母、蝶型螺母、盖型螺母、螺栓、梅型弹片、槽型螺母、焊接螺母、薄型螺母、内外牙锥母、防松螺母、塑胶螺母、阀螺母、管接头、倒帽、套筒等五金产品。

Placed outside the valve, must be covered with linoleum or Tarpaulins like rain, dust-proof materials.

放置室外的阀门，旋塞阀必需盖打油毡或大雨布之类防雨、防尘物品。

Improvement:(1) the first valve seat board improvement: file will be sealed by the "flat" shape to a "convex" shape.

改进方法：（1）座板阀的第一项改进：将上封盖由&平板&形，改为&凸&形。

Installed in the packing box above the gland flange, he bolts connecting the top of the valve cap.

安装在填料盒上面的是压盖法兰，他用螺栓与阀帽顶部连接。

Valve cap is the top of the workpiece is an important component, and as pressure parts for the body to provide a cap or lid.

阀帽是顶部工件的一个重要元件，并作为承压零件为阀体提供了帽或盖。

Nut Series: Hex flange nuts, rivet nuts, rivet stud pressure (through-hole and hole barrier), up rivet nut, nylon nut, with sets of teeth, K nut, square nuts, butterfly nuts, cap-type nut, bolts, Mei-type shrapnel, Groove nut, welding nut, thin nuts, conical teeth outside the mother, Nut, the plastic nut, valve nut, pipe joints, back caps, sleeves and other metal products.

螺母系列：六角法兰螺母、铆螺母、压铆螺柱、涨铆螺母、尼龙螺母、内套牙、K螺母、方螺母、蝶型螺母、盖型螺母、螺栓、梅型弹片、槽型螺母、焊接螺母、薄型螺母、内外牙锥母、防松螺母、塑胶螺母、阀螺母、管接头、倒帽、套筒等五金产品。

5 Degree of valve opening and closing valves open and close the display plate ① degree of scale line should be cast in the gearbox cover or change the direction of the display after the disc casing, all for the ground wire brush on the phosphor scale to show striking;② direct needle plate material in the case of better management of available stainless steel, or steel plate for the painting, do not make use of aluminum skin;③ direct drive needle eye-catching, stable fixation, accurate adjustment when opening and closing after Rivets should be locked.

4.5 阀门启闭程度的显示盘①阀门启闭程度的刻度线，应铸造在变速箱盖上或转换方向后的显示盘的外壳上，一律面向地面，刻度线刷上荧光粉，以示醒目；②指示盘针的材质在管理较好的情况下可用不锈钢板，否则氧气专用阀、铜阀门为刷漆的钢板，切勿使用铝皮制作；③指示盘针醒目，固定牢靠，一旦启闭调节准确后，应以铆钉锁定。

This will disengage the disc assembly, spring and seat cover into individual components.

这将把阀瓣总成、弹簧和阀座盖分解成独立的部件。

By decomposition of the inverse order of 50 loaded packing gland, stem stopper 66, spring washers 49, nut 48 fixed tight with the above-mentioned components.

9按分解的逆顺序依次装上填料压盖50、阀杆限位器66、弹簧垫圈49，用螺母48固紧上述零件。

He knows that he's one of the mostdominant players in the NBA right now.

我知道他现在是联盟里最有统治力的球员之一了。

Using analysis method of BCG , the dissertation analyzed the management of voluntary service organizations .

利用BCG分析方法对我国的志愿服务组织管理进行了分析。