装阀

Valve with is it regulate valve suit,flow of function to have.can be suitable for the occasion needing to control flow while being built-in,can also slow down the pressure head of the fluid.

阀腔内装以具有调节流量功能的阀套，可以适用于需要控制流量的场合，亦可以减缓流体的压力头。

By doing Micro-Controller, so as to wholly hydraulic cycle. Based on remaining the dismantling and loading, we make full of the equipped instrument. Several types of valves are linked through gluey tube.

通过单片机，实现整个实验台的控制，在保留其元件可拆装性的基础上，我们充分利用现有液压实验台的液压元件，对其基本回路进行重新组合，用调速阀，溢流阀，节流阀等通过胶皮管连接成所需要的回路。

Hydraulic control valve is a main valve and the exterior of the needle valve and a combination of the pilot valve.

水力控制阀是由一只主阀及其外装之针形阀和先导阀等组合而成。

At same time it collects the pr essure signal of Servo-cylinder, it finds that the overflow valve pr essure sets too high between the servo valve and Rodless cylinder servo cavity, Tanks should not stress-free cavity under unloading, According to the fuel tank pr essure signal.

摘 要：本文针对某热轧厂横切线上的主要设备矫直机在矫直高强度，厚规格产品时，当负载受到外扰动时，矫直机传动轴经常断，工作辊轴承经常损坏现象，于是对伺服缸压力信号进行采集，发现装在伺服阀出口和伺服缸无杆腔之间的溢流阀压力设置过高，油缸无杆腔压力不能卸荷。

The blowing inlet port can be divided into more than 10 forms, forming 1 to 4 different blowing directions. It can be used with bisecting multi-vane adjusting valve or single vane opening blast volume adjusting valve with a valve-board pattern.

按照扩散的形式可以分成10多种，可以形成1-4个不同的送风方向，可与对开多叶调节阀或单开阀板式风量调节阀配套使用，拆装方便。

Based on the work flow of charging equipment, three worst work conditions of the clack box were defined. Then, based on thermal-structure coupled theory, the thermal-structure coupled of the clack box which suffered from mechanical and temperature load was analyzed using the powerful software ANSYS. The clack box's temperature field and stress field as well as the stress spectrum of danger area in actual working condition were obtained. Finally, based on crack initiation and crack extension theory, the clack box's fatigue life was predicted.

摘 要：根据装料设备的工作流程，确定阀箱3种最不利的载荷工况；基于热－结构耦合理论并利用有限元分析软件ANSYS研究阀箱在温度载荷和机械载荷作用下的热－结构耦合问题，得到实际工况下阀箱的温度场、应力场以及危险部位的应力谱；依据裂纹萌生和扩展理论对阀箱进行疲劳寿命预测。

When the pump is installed on the position higher than the liquid level, it is necessary to mount a foot valve on the end of the suction pipe and its throat area should be 50% larger than the sectional area of the suction pipe.

泵安装在高于液面位置时，应在吸入管端装底阀，底阀喉口面积应大于吸入管截面积的百分之五十。

When the pump is installed on the position higher than the liquid level, it is necessary to mount a foot valve on the end of the suction pipeits throat area should be 50% larger than the sectional area of the suction pipe.

泵安装在高于液面位置时，应在吸入管端装底阀，底阀喉口面积应大于吸入管截面积的百分之五十。

The paper describes the reason why the 1000MW ultra supercritical steam turbine with HP single bypass valve using HP casing start-up was not applied with HP exhaust non-return valve and introduces the methods to prevent over-speed for load rejection,HP casing overtemperature and water admission.

论述了采用高压缸启动方式的带高压一级旁路的1000MW超超临界汽轮机不设高排逆止门的依据及其防止汽轮机甩负荷超速、高缸超温与进水的方法：一是在高压导汽管上加装通风阀，二是在冷再管上加装通往凝汽器的排汽管，三是在冷再管的低位加装能显示水位、自动报警及自动疏水的疏水罐。

Usually superimposed solenoid valve installed in the top of the block, so as long as the location of the interface can be superimposed alignment valve interface, even if the manual valve is possible.

通常把电磁阀装在叠加阀块的最上层，因此只要各接口的位置能够对准叠加阀的接口，即使使用手动换向阀都是可以的。

He is the most remarkable man that I have ever known.

他是我知道的人中最值得注意的人。

Increased appearance of lymphocele was noticed in patients with diabetic nephropathy, congenital malformations of the urinary tract, and inflammatory diseases, including glomerulopathy and extraglomerular ones, after high-voltage radiotherapy and after removal of the renal graft.

经过高压放射疗法和切除移植肾后，在糖尿病肾病患者、泌尿系统先天性畸形患者和炎症患者身上发现淋巴囊肿有所增加，包括肾小球病和球外疾病等。