溢流

In addition, because of the interleaving of top and bottom nappes, there is no bump in the air, the finite width of spillways can be fully utilized, and flood discharging atomization caused by bump of nappes can be weakened.

而且，表、深孔水舌在空中交错穿插，不发生空中碰撞，可充分利用有限的溢流宽度，并减少因水舌空中碰撞而导致的泄洪雾化的增强。

At the same time, large angular acceleration will cause impact in the hydraulic system.

溢流缓冲主要是降低瞬时压力冲击。建立相应的功率状态方程。

Though analysis and comparison,the appropriate angular aperture of runner and the interrelationship between overflow and exhaust system were achieved for the circular die casting.

分析比较得出适合圆形压铸件浇注系统设计时的横浇道张角夹角范围，以及溢流槽与排气槽之间位置尺寸相互影响的关系。

In order to realize the water level's stability of circulating cold pool for medium and heavy plate and avoid the overflowing,it is able to save energy and reduce pollution much better.

摘 要：为了实现中厚板浊环冷水池水位稳定，杜绝溢流，更好地节能减排。

The author advanced the elements of the geographic analysis techniques based on gridly DEM, which consists of the definition of ground surface topographic structure, the characteristic definition of combinatorial topographic units, analysis methods and algorithm design.

提出了基于栅格DEM的地学分析技术的组成部分，包括：地表特征形态结构定义、地理单元的组合特征定义、分析方法和算法设计；提出了形态特征分析和溢流分析相结合的方法来，剖面线集综合分析方法等新方法和新算法。

Since cordite burns at a greater rate at a higher pressure a relief valve must be used to allow generated gas to escape to atmosphere at times when the demand is low.

因为柯达火药在较高的压力下以较高的速度燃烧，所以必须使用一个溢流阀，以便当用气少时，能让所产生的部分气体排到大气中去。

Counterflow rinse system may use the same amount of water as a single overflow rinse, regardless of the number of compartments.

多室逆流清洗系统可以使用相等量的水作为单个溢流清洗，不管槽的数量为多少。

LIQUID FLOW MEASUREMENT IN OPEN CHANNELS BY WEIRS AND FLUMES.

NF X10-312-1986 用溢流堰和水槽法测量明渠中的液流。

At last, according to the effect of orifice configuration on the cavitation, the several poppet configurations of a relief valve were designed in order to suppress cavitation, the cavitating flow simulation for different configuration were performed and compared in ordet to find a optimal conriguration.

最后，针对阀口形状对气穴的影响，为了抑制阀口气穴，对溢流阀阀芯形状进行了改进，设计了几种不同的阀芯结构，分别对不同的阀芯进行了气穴流场分析和比较，来寻求优化的阀芯结构。

Traditional plastic injection molding machine relies on constant rate pump in oil supply, and each action in the process of plastic injection may have different requirements on speed and pressure. The surplus oil flows back to the oil tank through the proportioning valve in the way of flooding adjustment. In the whole process, the rotation speed of motor remains unchanged, so the oil volume is fixed as well. Furthermore, the action is intermittent, and not of full load, so a great amount of oil is wasted.

传统的注塑机是采用定量泵供油的，注塑过程的各个动作对速度、压力的要求也不一样，它是通过注塑机的比例阀采用溢流调节的方式将多余的油旁路流回油箱，在整个过程中，电机的转速是不变的，故供油量也是固定的，而由于执行动作是间隙性的，也并不可能是满负载的，因此定量供油就有很大的浪费空间。

I smile at your play with that little bit of a broken twig.

我微笑着看你玩那一段小小的树枝。

They may be produced for almost any shaft angle.

他们可能在制作中几乎任何一个轴角。