抗蚀

Erosibility and prbroin to reveal some of the glass, that is, you need to etch pattern.

抗蚀膜上露出玻璃的部分，即是需要蚀刻的图案。

Dichromate colloid solutions employed in photoengraving provide acid resists through the action of light on the sensitized surface.

重铬酸盐胶液是照相蚀刻版所用的感光液及抗蚀膜。光线的照射引起它的抗蚀作用。

The main characteristics, such as the matching behaviors of films coated on substrates in fabrication of concave cylinder photoresist microlens arrays, the structural parameter design of photoetching mask which is relevant to the fabrication of the microlens, and control basis of photoresist mask technological parameters, are analyzed respectively.

分析了在光致抗蚀剂柱凹微透镜图形制作过程中的膜系匹配特性，与制作该种微透镜有关的光掩模版的主要结构参数，以及光致抗蚀剂掩模工艺参数的控制依据等。

A multi-layered mask includes a lithographically patterned photoresist and an un-patterned organic antireflective coating formed over a substrate layer to be etched.

多层掩模包括形成在待刻蚀的衬底层上平版印刷图形化的光致抗蚀剂和未图形化的有机抗反射涂层。

The BARC layer is etched with a significant negative etch bias to reduce the critical dimension of the opening in the multi-layer mask below the lithographically define dimension in the photoresist.

使用有效的负性蚀刻偏置蚀刻该BARC层以减小在该多层掩模中的开口的特征尺寸至在该光致抗蚀剂中的平版印刷所确定的尺寸之下。

Thermoplastic etching is 7building, paraffine, bitumen, stearic acid, and prepared by adding a small amount of ofmaize-erosibility-erosibility powder create ink, print by thermal print, press the design pattern, squeegee the ink to the glass surface, forming a anti-erodibility film.

热塑性蚀刻丝印，是将石蜡、沥青、硬脂酸等所配制的粘合剂，加入少量的抗蚀粉调制成抗蚀印料，通过热印丝网版，按设计图样，把印料刮印至玻璃表面，形成抗蚀膜的。

The influence of solution treatment on mechanical properties of bellows was estimated; The corrosion-resistance of bellows was compared at different materials and states; The capability of anticorrosion of two states bellows in high-temperature oxidation and sulphidation environment was analyzed.

本研究讨论了影响波纹管发生腐蚀的介质及影响硫酸露点温度的因素；分析了波纹管固溶处理后表面残余应力的分布规律；评价了固溶处理对波纹管力学性能的影响；比较了不同材料、不同状态的波纹管耐蚀性能及两态波纹管在高温硫化-氧化环境下的抗蚀性能。

There are TAIHONG 2LPSE0503MW-250 single unadhesive ED flexible copper coated lamination and Nippon Steel CIPW-25080 single ED FCCL.Regards to photoresists, Dupont FX915 dry film would be the best choice for the production of COF FPC after the comparison in photosensitive property, resolution, adhesiveness and operating procedure between the different resist thicknesses of Dupont FX900 series.

光致抗蚀剂方面：通过对比杜邦FX900系列两种不同抗蚀层厚度干膜(FX930与FX915)的感光性能、分辨率、附着力、操作工艺等，确定出杜邦FX915(抗蚀层厚度15μm)为更适用于COF挠性印制板制作的干膜；并对干膜的曝光参数进行了优化，最佳曝光级数5级(相对于21级曝光尺)，曝光能量片式150mJ/cm~2、卷式110mJ/cm~2，使其更加适合于精细线路的制作。

Used in various inks and varnishes, and as an acid resist in photo -engravings.

用制各类油墨和清漆，并用作照相蚀刻版的抗蚀膜。

Although forest canopy layer could prevent splash erosion effectively, clay was taken away by overland flow and run off easily, the erosion amount became less after removing the forest canopy and surface soil, while the splash erosion still produced in the surface layer; the splash function weakened after having water current, the starting particles were less than bareland, so removing the surface disturbed soil made the erosion amount and clay less, silty sand more than bareland, but unsteady, the wear and tear energy used by raindrop splash and current function for overcoming sediments separating and starting were comparatively large, sediments were very difficult to be started and transported, it explained that forest root systems could increase anti-erosion capability of forest vegetation, make rainfall-current system splash and export finer particles than bareland.

虽然林冠层能有效防止溅蚀的发生，但坡面流还是能带走粘粒部分，粘粒还是容易流失。去除林冠和表层土后，侵蚀量变得更少，但表层还是会被溅蚀，有水流后，溅蚀作用减弱，颗粒起动的比裸地的少，所以，去除表层扰动土后，侵蚀量更少，粉沙多，粘粒比裸地更少一些，但不稳定，雨滴击溅和水流作用用于克服泥沙分离起动损耗的能量较大，很难被起动输移，这说明森林植被根系的作用增加了林地植被的抗蚀力，使降雨一水流系统仅能溅起输出比裸地坡面更细小的泥沙颗粒。

It is also known as one of the most poisonous naturally occurring substances.

它也被称为一个最自然发生的有毒物质。

The greatest stress is found at the location on the cross section where V is the largest.

最大应力出现在横截面上V为最大的地方。