圆柱

During the Renaissance, architects aimed to use columns, pilasters, and entablatures as an integrated system.

在文艺复兴时期，建筑师将圆柱、壁柱和柱上楣构作为完整的体系来使用。

The Crusaders thought it necessary to add to the four buttresses (only 51, 50 cm. thick) pilasters about 230cm. thick. Three of these have been recovered.

十字军认为需要加四根桥墩（只有50个，51公分厚）圆柱大约230公分厚，其中三根已经复原。

The bases were set deep down on the virgin rock. Only the visible pieces proofed of careful work. The pillars and pilasters were very finely made. The former were somewhat higher than the latter, and the four which supported the dome were 4.65 m. in size. They were topped by a moulding 25 cm. high. Their sides measured 143-145 cm.

圆柱的地基被深深地建筑在一座未开发的岩石上，只有显而意见的碎片能够证明这项精细的工程，石柱和方柱被建造的相当精致，前者比后者稍微高一些，四根支撑圆顶的石柱有4.65公尺高，石柱的顶端有25公分高的装饰板条，其侧面皆有143-145公分长。

The result illustrates that the influence of intercaction between phonons on ground state energy of exciton can not be ignored.

Luo〔2〕等人采用有效质量近似理论，在忽略表面极化子效应的情况下计算了球型、圆柱型和立方型量子点中激子的基态能量和束缚能。

In this dissertation, an automatic method is proposed to create cylindrical panoramas.

对于圆柱状全景图的建造，本文提出了一种鲁棒性较高的自动拼接方法。

Panettone, the tall, cylindrical, fruit-filled sweet bread from Milan has become an essential part of the Christmas season.

Panettone ，高大的圆柱，水果，甜面包填补从米兰已成为一个重要组成部分的圣诞节。

To make the transition curve in the process of gear modeling be more reasonable, the parameterized 3D model of involute cylindrical spur gears with whole profile was made with Pro/Engineer software, based on the study of equations of the dual-arc rack cutter＇ s profile curves and the cut gear＇ s tooth profile curves.

为了使齿轮建模时过渡曲线部分更符合工程实际，在对双圆弧齿条型刀具轮廓曲线方程和齿轮的廊线方程研究的基础上，利用Pro/Engineer软件建立了可变位的渐开线完整齿廊直齿圆柱齿轮的三维参数化模型，并对齿廊曲线连续性进行了分析。

Included are the measurements of the tooth profile deviation of a shaving cutter based on the generalized polar coordinate method, and of the helix deviation of the shaving cutter using curvature method to automatically identify the boundary points; the measurements of the tooth profile of a modified hobbing cutter, and of deviation of contact line of the hobbing cutter by means of the generalized cylindrical coordinate method; the measurement of the deviation of tooth profile of a non-linear worm .

这些测量包括：①基于广义极坐标法的剃齿刀齿廓误差测量，以及采用&曲率法&自动识别界点的剃齿刀螺旋线误差的测量；②修形滚刀的齿廓测量，以及基于广义圆柱坐标法的滚刀啮合误差的测量；③非线性蜗杆的齿廓误差测量。

Shandong Zouping Mingbo Power Source Co., Ltd. specializes in research and development, producing AAA, 1/2AA, 2/3AA, 4/5AA, AA, A, 2/3N, 4/5N, N, SC, 5/4C, C, 2/3D, D,1870 types cylindrical NiCad and NI-MH rechargeable batteries. We can provide other size and capacity of the battery according to requirement.

邹平铭波电源有限公司专业致力于镍镉和镍氢充电电池的研究开发，生产圆柱型AAA， 1/2AA，2/3AA， 4/5AA， AA， A， 2/3N， 4/5N， N，SC， 5/4C， C， 2/3D， D，1870系列型号镍镉、镍氢充电电池，也可根据客户需求定制不同尺寸容量规格的电池或电池组。

The pillars which divided the naves rested on two bases.

把中殿分开的圆柱是建置於两个地基上。

I smile at your play with that little bit of a broken twig.

我微笑着看你玩那一段小小的树枝。

They may be produced for almost any shaft angle.

他们可能在制作中几乎任何一个轴角。