查询词典 width

Results The sexual dimorphism of the arch width in most of groups divided by age and position was significant.

结果 牙弓宽度在多数年龄组、分段中存在显著性别差异。

With an overall width of 42 1/2" and down height under 51 3/4", the Dinkey will fit through most commercial sized doorways.

设备宽度在42 1/2英寸，上下高度在51 3/4英寸，Dinkey适合所有的商业尺寸。

Compared with diploidy seedlings of P.elongate,leaf length and stomata size of tetraploid becomes bigger,the leaf length/width ratio and stomata density becomes smaller.

变异植株叶片比二倍体大，叶片长宽比变小，叶片单个气孔变大，气孔密度变小。

According to the image lane marking parameter information,not the position and direction of the parameter estimation model in the current traffic lane were established, but also the establishment of a lane width of the model.

建立了车辆在当前车道中位置参数、方向参数以及车道宽度估计模型。

The dispersoid distribution of the second phase could strengthen the surface of the alloy, which decreased the quantity of abrasive particles. The wear volume of the alloy was decreased. The hardness and strength of the alloy were increased after ECAE. The resistance of deformation was improved and the depth and width of furrows were decreased due to the increase of hardness and strength. As a result, the wear-resistance and tribological properties of the alloy were improved after ECAE.

ECAE热挤压处理显著细化了铝青铜合金的微观组织，弥散分布的第二相对合金起到强化作用，减少了剥落磨粒的数量，降低了合金的磨损量；ECAE热挤压处理的铝青铜合金组织细小，强度和硬度高，提高了合金抵抗塑性变形能力，减轻了磨粒对合金表面的犁削作用，提高了合金的摩擦磨损性能。

Number display, and control cycle interval, pulse interval and pulse width, so as to control dust-clearing

本控制仪核心控制由单片机实行，实现按键参数设定、数码显示及循环间隔、脉冲间隔和脉

Number display, and control cycle interval, pulse interval and pulse width, so as to control dust

DMK-4CSA5 本控制仪核心控制由单片机实行，实现按键参数设定、数码显示及循环间隔、脉冲间隔和脉冲

Ray height and ray width can be used for diagnostic or subsidiary diagnostic features to distinguish S. ovata from other Sonneratia species.

结果表明1。射线高度和射线宽度可作为卵叶海桑区别于其它种类的鉴定特征或辅助特征；2。

It is clearly that only two geometrical parameters i.e. maximal misalignment angle and distortion width need to be determined experimentally.The engineering constants around the stitch hole in the composite laminate are analyzed using the FDM.

采用纤维弯曲模型分析了缝纫复合材料单层在缝纫孔附近的最大纤维偏转角、缝纫影响区以及缝纫复合材料单层及层合板工程常数的变化，发现工程常数具有很明显的区域性，能够看出各层中树脂富集区的痕迹。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

Chimborazo and Cotopaxi, took me by the hand.

越过琴博腊索山和科托帕克西山。

This car is in a good condition.

这辆车的状况很好。