查询词典 wake flow

First, free wake analysis was carried out to calculate the rotor wake geometry and the downwash around the engine jet space.

首先应用自由尾流分析技术来计算旋翼尾迹和发动机绕排流空间的洗流速度。

With all the weather related problems we've had lately, it's a big relief to wake up and realize that the power is still on, and I don't need that little camp stove to make my wake-up cup of coffee.

与天气有关的问题，我们都不会忘记近来它的一大觉醒和救助力量仍然意识到，不用说，我把我的小火炉阵营催醒喝杯咖啡。

Wake me up. Bid my blood to run. I can''t wake up.

唤醒我，激活我的血液，我不能沉睡。

In accordance with the established design flow and design of lift in the type spectrum, the first ordinate in order to design the head to find out the requirements in line with the head, while the flow ranging from a few pumps, and then in the abscissa in order to design the flow to determine the selection of What kind of pump.

根据确定的设计流量和设计扬程，在型谱图上，首先在纵坐标上以设计扬程查找出符合扬程要求。而流量不等的几种水泵，然后再在横坐标上以设计流量来确定选用哪一种水泵。

, though particles are not in the flow passage of the outlet of the impeller, the absolute velocity of particles has a component velocity whose whirling direction is the same as that of the impeller under the influence of the revolving impeller, in addition, particles do not flow toward the outlet of the impeller, instead, they flow toward the inlet of impeller.

款 尽管粒子是不是在流道叶轮，绝对速度的粒子的一个组成部分，其速度旋转方向是相同的叶轮的影响下， 3777叶轮，此外，颗粒不流向叶轮，相反，它们流向导流叶轮。

In this paper, the bump patterns for flip-chip packages are discussed first, then an experiment is setup to study the dispensing phenomena for different bump patterns, and the CAE software is used to analyze and identify with experiment mutually. From these thorough comparisons and analytical analysis, the existence of channel could slow down the flow, the high density of bump could speed up the flow, and it could avoid the air trap by modified the bump and channel's arrangement on flip-chip package. Then flows in rectangular microchannels driven by capillary force and gravity are discussed; furthermore, the theoretical model of flow in microchannel driven by capillary force and gravity is formulated from the Navier-Stokes equations.

本文首先针对覆晶底部充填进行相关理论推导、实验与模拟，探讨不同凸块配置模型所造成的波前不平滑现象对底部充填流动的影响；即依据相关参数建立模型进行底部充填实验，同时以CAE(Computer-Aided Engineering)模流分析软体进行模拟，在完成理论探讨、实验与模拟分析之后，交叉比较理论、实验与模拟分析结果，归纳出影响底胶充填流动之因素，由结果显示在凸块密集度较高的区域，凸块可以帮助流动，但是在凸块区后方的沟槽区域则因为凸块区所提供之流量不足，所以会造成波前落后的现象，另外藉由修改凸块与沟槽配置的关系，可以有效的控制波前形状的变化情形，避免产生包风现象。

The hot-wire anemometry was also used to characterize the air flow patterns that were generated by high and low swirl port in a cylinder of a steady-flow rig. Some important phenomena of air flow in the simulative cylinder were found.

借助于热线风速仪研究了两种不同的螺旋进气道在稳流气道试验台的模拟气缸中产生的流场结构，发现了一些重要的现象。

It is shown that laser anemometry, as a non-intrusive anemometer, is more suitable and convenient than traditional instruments in application to rotational flow fields, especially to the flow within centrifugal impellers which have only small width of flow passage.

研究表明，激光测速仪作为一种先进的非接触式测速仪器在旋转流场特别是流道高度很小的离心旋转流场的研究中较之传统仪器更合适、更方便。

ABSTRACT In this paper, an investigation on the helical ports was carried out in a steady-flow rig. The three velocity Components of air flow through the intake valve of several typical helical ports were measured by hot-wire anemometry for analysing the relationships between intake port geometry and swirl level as well as flow resistance.

本文在稳流气道试验台上对螺旋进气道进行了大量的研究，为了分析螺旋进气道的结构形状与涡流强度及流动阻力的关系，采用热线风速仪测量并分析了不同气道的气门口气体流速。

By using Laser Doppler Anemometry, the local liquid velocity profiles of the single-phase flow and two-phase crossing flow were measured on a sieve tray simulator. The effect of gas on liquid under crossing flow was studied.

本文通过使用激光多普勒测速仪对矩形塔板上液相单相流和气液错流情况下的局部液相流场进行测量，考察了气液错流时气相对其周围局部液相流场的影响。

The teacher likes the honeymouthed little girl very much.

老师很喜欢这个嘴甜的小姑娘。

Mr. Notker Bien's interests are traveling, spending quality time with the family and long-distance-running.

诺特卡·柏恩先生热爱旅游，长跑，以及和家人一起共度美好时光。