查询词典 upper bend

Radius of a bend: take the biggest radius of a bend of a cable, oil pipe, gas pipe or water pipe as a reference value and leave 10% of the space as a margin.

内宽：选择较粗的一些电缆油管气管水管等，其外径之和作为拖链内宽的参照，并留有至少10%的宽度空间。

It has the function about arithmetic auto-produce,the test bulletin auto-compile also.Debugging and system's exploitation become more convenienter.It can calculability the max force,the bend force,the no-votable bend force,the average peeling off force,the modulus of elasticity,etc.

还具有算法自动生成、试验报告自动编辑功能；大大方便了调试和系统再开发能力，可计算最大力、屈服力、非比例屈服力、平均剥离力、弹性模量等参数；使用高精度的测量仪器，集高度自动化、智能化于一体。

A clockwise bend is 45 degrees lag, a counterclockwise bend is 45 degrees lead.

顺时针的弯曲表示落后45度，逆时针的弯曲则代表45度提前。

The Periscope Drawtube will be bent because of the water resistance in sailing and this bend will cause the error of star measurement. Due to its especial structure, contactless measurement is the only way to measure its bend degree. First this paper introduces the method by linear array CCD based on structure and light path; Second it expatiates linear array CCD work principle and driving scheduling with example of TCD1501C and the driving circuit by CPLD. The output signal of linear array CCD includes common disturbance so the differential amplifier is needed. In order to make the signal adapt to computer processing, a threshold circuit with Schmitt characteristic and the data process following threshold are given. At last, some key problems in application are given.

潜艇潜望镜的镜筒在航行时受到水的阻力会产生弯曲变形，这种变形会造成潜艇对星体测量的误差；由于镜筒结构的特殊性，对其弯曲程度的测量只能采用非接触方法；首先从结构和光路方面介绍采用线阵CCD作为检测元件实现对镜筒弯曲程度的测量；其次以东芝公司的线阵CCD（TCD1501C）为例阐述了其工作原理及驱动时序的控制要点，并介绍了基于可编程逻辑器件的线阵CCD的驱动电路；线阵CCD输出的信号中含有共模干扰，必须采用差分放大器将其抑制；为将信号转化为适合计算机处理的数字信号，文中给出了有一定实用价值具有施密特特性的二值化处理电路及二值化后的数据处理过程；最后阐述了在实际使用中的一些关键问题。

In this article, based on the mechanic model of throttle-slice, the bend deform differential equation is founded, the formula and coefficient of elastic throttle-slice bend deformation are created.

通过减振器节流阀片的力学模型，建立了节流阀片弯曲变形的微分方程，得到了阀片弯曲变形系数和在任意位置的弯曲变形计算公式。

Under normal circumstances a 90-degree elbow bend resistance than 120 degrees, and each 90-degree bend head loss of about 0.5 ~ 1 m, each 20 m pipeline will enable the head of the resistance loss of about 1 meter.

一般情况下90度弯管比120度弯管阻力大，每一90度弯管扬程损失约0.5～1米，每20米管道的阻力可使扬程损失约1米。

The double sheet bend is more secure than the single sheet bend and is used when there is a great difference in the size of the rope.

双接绳结比单接绳结更为安全，用于联结粗细差异较大的两条绳索。

Analyzing the proved experiences of four kinds of end-bend models, and assuming a minor deviation, with the application of the aforementioned total pressure coefficient and deviation calculation model on the undesigning operating condition, numerical estimate is done on the characteristics change at designing rotating speed (n＝1. 0) after applying five various kinds of end-bend models.

总结了国内外有过成功经历的4种端弯模式，并且在小偏离假设下，应用上述非设计工况总压损失系数和落后角计算模型，对74A压气机采用5种不同的端弯模式后，在设计换算转速（n=1.0）下的特性改变情况进行了数值预测。

This picture shows a great way to get a good bend that will start where it's supposed to and leave and prior tubing to the bend unmolested.

这张照片显示，一个伟大的方式取得了良好的弯曲，将地方开始，它的假定和离开之前，油管，以弯曲

Experiments exposed that the inner flow of tooth space in the micro-channels was proved to be cycled flow after fully development. For the more, low velocity vortex cavities existed in the vertex angle and inner side of bend angle of straight angle micro-channel, while back flow only appeared in the internal side of bend angle of round angle micro-channel. It's easy to take place deposition in the low velocity vortex cavities, which is the main cause of blocking.

试验发现各类微通道齿间内流充分发展后是一种重复性流动，平角微通道顶角和转角内侧存在低速涡旋区，圆角微通道只在转角内侧出现回流，颗粒在低速涡旋区易发生沉积，是造成堵塞的主要原因。

Sodium citrate; calcium carbonate; calcium hydroxide; potassium bicorbonate; magnesium carbonate; ferrous sulphate; Zinc sulphate; copper sulphate; manganese sulphate; potassium iodide; sodium selenite.

柠檬酸钠；碳酸钙；氢氧化钙；碳酸氢钾；碳酸镁；硫酸亚铁；硫酸锌；硫酸铜；硫酸锰；碘化钾；亚硒酸钠。

All this to say that I'm glad filmmaking hasn't become completely ironic. I can enjoy an ironic film as much as the next person, but they usually involve a message of some sort. One that's delivered in a smirkingly clever way that requires little in the way of talent.

所有这些都是说，我很高兴电影制作没有变成完全讽刺艺术，我可以和下一个人一样享受讽刺电影的乐趣，虽然他们经常会被划归到一定级别，技术方面不需要很高的才能。